all motor b16a calibration in need!!
all motor b16a calibration in need!!
Iv got a freshley rebuilt b16a with 17, 000km on it. Has a header back 2.5inch magnaflow exhaust, password jdm intake, a set of 2001 USDM ITR cams and springs. Stock Iinjectors. Using a jdm b16 basemap right now but I feel like a little more could be pushed out of it. Runs a bit rich I fined but thats the least of my worries.New to thd Hondata system and dont want to screw something up on my build. All help Iis appriciated!!
Re: all motor b16a calibration in need!!
I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
- Attachments
-
- Wfb8922 16a.skl
- (40.05 KiB) Downloaded 631 times
Mrs Autoparts @ Honda Parts Malaysia
-
- Posts: 110
- Joined: Sun Aug 28, 2011 11:41 pm
Re: all motor b16a calibration in need!!
only tune I have that has your setup. This car ran good with this tune
- Attachments
-
- Enrique Garcia B16a2 WB.skl
- (40.04 KiB) Downloaded 669 times
-
- Posts: 2
- Joined: Wed May 06, 2015 8:13 pm
Re: all motor b16a calibration in need!!
Hi do you have basemap for Injen CAI with 421 headers and 2.5 exhaust? I am doing an engine build soon so I don't want to tune my car yet. Thank you!!!cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
Re: all motor b16a calibration in need!!
Hi do you have basemap for Injen CAI with 421 headers and 2.5 exhaust? I am doing an engine build soon so I don't want to tune my car yet. Thank you.Kevinbrahh wrote:cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
Look for this attachment
Mrs Autoparts @ Honda Parts Malaysia
Re: all motor b16a calibration in need!!
I know this is a very old thread but could really use your help.cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
Wfb8922 16a.skl
I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.
Please suggest the best possible basemap you have that matches to the mods below:
B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.
Hope to hear from you soon.
Thanks & regards
Dev
Thanks & Regards
------------------------------
Ecronic
------------------------------
Ecronic
-
- Posts: 100
- Joined: Thu Jul 14, 2016 12:32 pm
- Location: Fresno,Ca
Re: all motor b16a calibration in need!!
Hey Dev, you should be able to run your car with a hondata s300 basemap (b16/p30 map). Since you only have minor mods it should be capable to run your car.ecronic wrote:I know this is a very old thread but could really use your help.cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
Wfb8922 16a.skl
I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.
Please suggest the best possible basemap you have that matches to the mods below:
B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.
Hope to hear from you soon.
Thanks & regards
Dev
Re: all motor b16a calibration in need!!
Hi ZperformanceZperformance wrote:Hey Dev, you should be able to run your car with a hondata s300 basemap (b16/p30 map). Since you only have minor mods it should be capable to run your car.ecronic wrote:I know this is a very old thread but could really use your help.cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
Wfb8922 16a.skl
I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.
Please suggest the best possible basemap you have that matches to the mods below:
B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.
Hope to hear from you soon.
Thanks & regards
Dev
Thanks for replying. I'm just worried about running lean or rich. I've got afr gauge installed so guess I'm going to go ahead with that map and post the result. Let's hope someone can help out then setting up the fuel tables.
Cheers
Dev
-
- Posts: 100
- Joined: Thu Jul 14, 2016 12:32 pm
- Location: Fresno,Ca
Re: all motor b16a calibration in need!!
Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.
Re: all motor b16a calibration in need!!
Okay so I tried the s300 cal for b16a/ p30 & the check engine light came on. Errors that shoot up are oxygen sensor heater & knock sensor. My stock ecu doesn't have any errors.Zperformance wrote:Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.
Fyi
Stock ecu: P30 & s300 ecu: p28
Appreciate you replying my posts Zperformance and thanks to anyone who can some light on this.
Cheers
Dev
-
- Posts: 100
- Joined: Thu Jul 14, 2016 12:32 pm
- Location: Fresno,Ca
Re: all motor b16a calibration in need!!
Go through the paramateres and you can disable it. If you are not sure, let me know i will disable them and upload it here for you.ecronic wrote:Okay so I tried the s300 cal for b16a/ p30 & the check engine light came on. Errors that shoot up are oxygen sensor heater & knock sensor. My stock ecu doesn't have any errors.Zperformance wrote:Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.
Fyi
Stock ecu: P30 & s300 ecu: p28
Appreciate you replying my posts Zperformance and thanks to anyone who can some light on this.
Cheers
Dev
-
- Posts: 100
- Joined: Thu Jul 14, 2016 12:32 pm
- Location: Fresno,Ca
Re: all motor b16a calibration in need!!
basically P30 basemap i just disable the sensors
- Attachments
-
- P30.skl
- *use at your own risk
- (45.57 KiB) Downloaded 257 times