SManager V2.2.7 (beta)
Re: SManager V2.2.5 (beta)
i thought, that there wasn't a timer on the chip.
just a mistake by me.
those kind of requests are in the software request thread.
but this is a thread, where you answer. that's really great.
i think, everybody is looking for such a support.
just as I sad: idea - pros/cons - you know, what we would like to have. we know if it's possible.
EDIT: really sorry, Hondata. although I work with the software for so long, but I've never seen that export option! just knew that video export thingy.
my fault! really sorry for that.
best regards Lukas
just a mistake by me.
those kind of requests are in the software request thread.
but this is a thread, where you answer. that's really great.
i think, everybody is looking for such a support.
just as I sad: idea - pros/cons - you know, what we would like to have. we know if it's possible.
EDIT: really sorry, Hondata. although I work with the software for so long, but I've never seen that export option! just knew that video export thingy.
my fault! really sorry for that.
best regards Lukas
Re: SManager V2.2.5 (beta)
Hondata wrote:Lukas, you'll need to clarify your response.
What do you mean about an on-chip timer? What is the purpose of this?
Why can't you export datalogs and use the data that way?
This should be in the software requests thread, so I may move the posts over.
becoz the dataset of the datalog export is (very) limited
-
- Posts: 4
- Joined: Fri Feb 08, 2013 10:48 pm
Re: SManager V2.2.5 (beta)
Is there some reason why we can't add more than 20 rows to the ignition and fuel tables?
Re: SManager V2.2.5 (beta)
use boost tableswhiterabbit wrote:Is there some reason why we can't add more than 20 rows to the ignition and fuel tables?
Re: SManager V2.2.5 (beta)
he said ROWS not COLUMNS.Johnny_9 wrote:use boost tableswhiterabbit wrote:Is there some reason why we can't add more than 20 rows to the ignition and fuel tables?
www.MSSRACING.com
9.29 | 6.20 | 167
9.29 | 6.20 | 167
Re: SManager V2.2.5 (beta)
a nice checkbox that would be good is to disable burnout rev limiter overriding launch limiter (to make use of antilag, and soft limiter for initializing burnout)
www.MSSRACING.com
9.29 | 6.20 | 167
9.29 | 6.20 | 167
Re: SManager V2.2.6 (beta)
Notice a problem with the Flex Fuel and Close Loop operation (V2.2.6 beta).
Flex Fuel Voltage compensation starts and ends with 5 volts.
Close Loop operation does not take affect until you open and close the setting window.
Flex Fuel Voltage compensation starts and ends with 5 volts.
Close Loop operation does not take affect until you open and close the setting window.
Re: SManager V2.2.6 (beta)
Can you be more specific? Do you mean the ethanol content compensation table? It goes from 0V to 5V here. If not, post the calibration.
Closed loop operation - do you mean that the ECU runs in open loop, or is there some other setting which changes when you open and close the settings window?
Closed loop operation - do you mean that the ECU runs in open loop, or is there some other setting which changes when you open and close the settings window?
Hondata
Re: SManager V2.2.6 (beta)
Flex Fuel - after saving calibration it reverts back to the first voltage been 5 volts not 0 volts.
Close Loop - If I'm to switch from open loop to close loop wideband input the other parameters (conditional, short term fuel trim, rate of change) are not activated until I open and close setting window.
Close Loop - If I'm to switch from open loop to close loop wideband input the other parameters (conditional, short term fuel trim, rate of change) are not activated until I open and close setting window.
- Attachments
-
- Normal Index.skl
- (42.29 KiB) Downloaded 150 times
Re: SManager V2.2.6 (beta)
getting this error after install AND restarting. getting it when i try to open a calibration by double clicking the file. I can load the file from FILE OPEN just fine. This happens with any calibration as well.
see attached.
see attached.
- Attachments
-
- error message
- error.jpg (18.94 KiB) Viewed 13541 times
www.MSSRACING.com
9.29 | 6.20 | 167
9.29 | 6.20 | 167
-
- Posts: 27
- Joined: Sun Nov 18, 2012 9:12 pm
Re: SManager V2.2.6 (beta)
Same thing here!SPOOLIN wrote:getting this error after install AND restarting. getting it when i try to open a calibration by double clicking the file. I can load the file from FILE OPEN just fine. This happens with any calibration as well.
see attached.
Re: SManager V2.2.6 (beta)
Thanks for the report. We've fixed this and will make another release today.
Hondata