K-Manager - Verify Feature

K-Series Programmable ECU installation questions / support issues
Locked
kwanjie
Posts: 1
Joined: Wed May 19, 2004 1:30 am

K-Manager - Verify Feature

Post by kwanjie » Wed May 19, 2004 1:32 am

I accidentally did Verify while my car was on.... does that do any harm?

User avatar
Hondata
Site Admin
Posts: 8774
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Verify

Post by Hondata » Thu May 20, 2004 2:34 pm

No. You don't really need to verify as this is performed automatically while uploading.
Hondata

lanman2000
Posts: 6
Joined: Fri Jan 23, 2004 12:14 am

Post by lanman2000 » Sat Jul 24, 2004 12:04 am

what if the verify feature says there are 151 errors?? is that a problem??

User avatar
Spunkster
Site Admin
Posts: 18006
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Post by Spunkster » Mon Jul 26, 2004 10:36 am

If there are any errors when using the verify then you will need to close the software, reopen it , reload the calibration, then re-upload the file. Then verify the calibration to make sure there are no errors.

ares650
Posts: 68
Joined: Sun Jul 11, 2004 10:08 pm

Post by ares650 » Wed Jul 28, 2004 5:35 pm

What changes can be done while the motor is running? Can I do any on the fly changes to a map?

User avatar
Spunkster
Site Admin
Posts: 18006
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Post by Spunkster » Thu Jul 29, 2004 9:55 am

It is not recommended to do any changes while driving the car. You may be able to make a small change while the engine is running, but again, THIS IS NOT RECOMMENDED.

ares650
Posts: 68
Joined: Sun Jul 11, 2004 10:08 pm

Post by ares650 » Fri Jul 30, 2004 8:29 am

Spunkster wrote:It is not recommended to do any changes while driving the car. You may be able to make a small change while the engine is running, but again, THIS IS NOT RECOMMENDED.
Why is it not recommended? Cause it a shut down the engine or harm the ECU. I don't mean while driving the car, just running the motorer.

GTI
Posts: 18
Joined: Tue Oct 14, 2003 6:51 pm

Post by GTI » Fri Sep 24, 2004 6:01 pm

The engine may stall, but not always.
Other than that I do not have any problem.
I have been doing it since day one.

User avatar
Spunkster
Site Admin
Posts: 18006
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Post by Spunkster » Mon Sep 27, 2004 9:15 am

Keep in mind that you will have to wait 10 seconds for the ecu to come out of startup mode everytime you upload to it. Until then the cams will be locked at the 0 position.

midnight runner
Posts: 1
Joined: Fri Oct 29, 2004 11:26 pm
Contact:

Post by midnight runner » Mon Nov 01, 2004 1:18 am

Spunkster wrote:If there are any errors when using the verify then you will need to close the software, reopen it , reload the calibration, then re-upload the file. Then verify the calibration to make sure there are no errors.
i did that.. and it still says there are 40 errors. i did it with two different calibrations also. Am i doing something wrong?

will it hurt to run the car with errors?

Locked