SManager V1-1 Beta
-
- Posts: 23
- Joined: Sat Sep 10, 2005 8:57 pm
-
- Posts: 23
- Joined: Sat Sep 10, 2005 8:57 pm
calibration and offset are two different things.
the calibration is the accuracy of the output of the wbo2.
the offset is the agreement of the wbo2 and the ecu datalog.
that is in simple terms, but do you see the difference in terms?
the calibration is the accuracy of the output of the wbo2.
the offset is the agreement of the wbo2 and the ecu datalog.
that is in simple terms, but do you see the difference in terms?
RaVer Motorsports (559) 733-4711
ravermotorsports@earthlink.net
ravermotorsports@earthlink.net
-
- Posts: 100
- Joined: Tue Jun 07, 2005 3:19 pm
ran into a problem with the system today. tried tuning my idle and part throttle areas but it is as if the ecu is not responding to the changes real time. i have to save, upload, then startup again for the changes to work. can't adjust idle speed but the iac control works. can't adjust fuel without having to restart. car is running good with the exeption of these problems. when will the final version be released?
-
- Posts: 100
- Joined: Tue Jun 07, 2005 3:19 pm
-
- Posts: 100
- Joined: Tue Jun 07, 2005 3:19 pm
got the car running pretty good so i decided to drive it around the block. did a few runs but didnt run open loop, just wanted to see how things were. we'll it works out pretty good. only problem now is that when i went into WOT the displays in smanager went crazy again. got a bunch of unknown error codes, erraneous display readings such as rpm, map, etc. what would cause this? things were working perfect until the WOT run. i restarted from idle and it datalogged perfect.
-
- Posts: 100
- Joined: Tue Jun 07, 2005 3:19 pm
-
- Posts: 100
- Joined: Tue Jun 07, 2005 3:19 pm
new list of problems after installing a fresh version of smanager and usb drivers:
- get a "floating point division by zero" error when i try to datalog or review a saved datalog. it just pops up a million times when i hit f9. this is with the usp30 basemap.
- car idles fine for a couple seconds then the a/f rapidly drops from 14.7>13>12.xx. i can get the car to stay at 14.7 but what causes this? i have new plugs, wires, o2.
- still can't get the car to idle at the set 800rpm. lowest is 950rpm even with the iacv duty to the lowest and 0 for water and air comp.
- when i try to install the cd version (1.0.09) i also get an error saying it detects a newer version on the comp even though i have uninstalled both smanager and the usb drivers.
- on knock voltage is 0v a good thing or 5v? before i did this fresh install i was getting 0v. now even at idle it is at 5v.
car setup:
stock b17
ngk bkr6es-11 spark plugs
ngk spark plug wires
mobil 1 synthetic 5w-30
2.5" exhaust
am i doing something wrong or is it the program itself? when i upload i put the car to on, upload, remove the key, then start the car.
- get a "floating point division by zero" error when i try to datalog or review a saved datalog. it just pops up a million times when i hit f9. this is with the usp30 basemap.
- car idles fine for a couple seconds then the a/f rapidly drops from 14.7>13>12.xx. i can get the car to stay at 14.7 but what causes this? i have new plugs, wires, o2.
- still can't get the car to idle at the set 800rpm. lowest is 950rpm even with the iacv duty to the lowest and 0 for water and air comp.
- when i try to install the cd version (1.0.09) i also get an error saying it detects a newer version on the comp even though i have uninstalled both smanager and the usb drivers.
- on knock voltage is 0v a good thing or 5v? before i did this fresh install i was getting 0v. now even at idle it is at 5v.
car setup:
stock b17
ngk bkr6es-11 spark plugs
ngk spark plug wires
mobil 1 synthetic 5w-30
2.5" exhaust
am i doing something wrong or is it the program itself? when i upload i put the car to on, upload, remove the key, then start the car.