CTR FlashPro tuning - fuel pump
-
- Posts: 1
- Joined: Wed Jun 03, 2020 1:55 pm
Re: CTR FlashPro tuning - fuel pump
I have Flashed my 2018CTR and installed the high pressure fuel system upgrade.
The Falshpro will not allow me to enter the serial number and software key.
Tried everything and Hondata has been unable to help so far.
The Falshpro will not allow me to enter the serial number and software key.
Tried everything and Hondata has been unable to help so far.
Re: CTR FlashPro tuning - fuel pump
Have you contacted us yet? Please email support@hondata.com with the serial number you are using.
Hondata
Re: CTR FlashPro tuning - fuel pump
This was resolved yesterday, it had already been activated in the software.
Re: CTR FlashPro tuning - fuel pump
What’s the duty cycle on the factory map? Also 95%?
Do the Hondata maps have the air charge adjusted to ensure duty cycle doesn’t exceed 95%, or is it critical that the end user periodically performs data logging just to confirm?
Do the Hondata maps have the air charge adjusted to ensure duty cycle doesn’t exceed 95%, or is it critical that the end user periodically performs data logging just to confirm?
Re: CTR FlashPro tuning - fuel pump
Do you mean the fuel pump duty cycle with the Hondata Fuel System? It depends on the fuel used. I believe it is around 70% on pump fuel.
And the answer to the second question is that it is a good idea to check knock retard, lambda and fuel pump duty cycle on any vehicle.
And the answer to the second question is that it is a good idea to check knock retard, lambda and fuel pump duty cycle on any vehicle.
Hondata
Re: CTR FlashPro tuning - fuel pump
I meant the duty cycle on a completely factory car (factory map, factory fuel system, etc).Hondata wrote: ↑Sun Jun 21, 2020 6:33 am Do you mean the fuel pump duty cycle with the Hondata Fuel System? It depends on the fuel used. I believe it is around 70% on pump fuel.
And the answer to the second question is that it is a good idea to check knock retard, lambda and fuel pump duty cycle on any vehicle.
Re: CTR FlashPro tuning - fuel pump
You can't datalog from a 100% factory vehicle because it does not datalog the fuel pump duty. But I'd guess it is around 80%. Duty is not linear with volume however, so it is not 80% of capacity. What are you trying to determine?
Hondata
Re: CTR FlashPro tuning - fuel pump
I was just trying to compare the duty cycle of a factory tune with a Hondata tune but it doesn't sound like the percentages are linear, which makes it difficult to compare.
Re: CTR FlashPro tuning - fuel pump
I am running full bolt and meth kit & my fuel duty cycle has hit 100% on some WOT pulls and I experience sputtering . Can I get some help with what I could do?
Re: CTR FlashPro tuning - fuel pump
I am having an issue where after fuel system installation my flashpro automatically says pump enabled and will not let me put the serial and software key. I need help on hot to know if it is working or not so confused right now. Please see attached screenshots
- Attachments
-
- 6B70195E-2CCA-4C72-9013-063795AEAFE0.png (986.29 KiB) Viewed 5648 times
-
- E6E6CFDA-1D8A-453D-8533-286F0FD8CC54.jpeg (84.06 KiB) Viewed 5648 times
Re: CTR FlashPro tuning - fuel pump
If it shows enabled then you do not need to do anything further. I also answered the feedback information you sent.
Hondata
Re: CTR FlashPro tuning - fuel pump
Thank you! I just wanted to make sure everything looked good before I push the car for some datalogs