Random lean condition after shift to third gear

FlashPro questions & answers specific to the 2007-2012 Acura RDX
Post Reply
D-Rob
Posts: 67
Joined: Tue Apr 29, 2008 6:11 am

Random lean condition after shift to third gear

Post by D-Rob »

Hello,

After tuning a buddy's test mule RDX on E85, I have found that right after the shift to third gear on a 1-2-3 run, the commanded injector pulse is much lower than it should be for a second or two, then richens up in an instant; whereas this is not the case in second gear or fourth gear after the shift.

At first I thought it was because the engine made more than 17psi (where the WOT Compensation table stops natively), so I edited the load index on the last column to 20psi (and made the appropriate changes to the values there), and the same issue exists.

We did not run into this on the dyno (doing third gear runs), and only see it on the street after the 2-3 shift.

Any insight on what I'm seeing here?
Street_Lean3rdGearShift.fpdl
Lean condition in third gear for a moment.
(9.49 KiB) Downloaded 317 times
Thank you.
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Random lean condition after shift to third gear

Post by Hondata »

Can you send us the calibration too?
Hondata
D-Rob
Posts: 67
Joined: Tue Apr 29, 2008 6:11 am

Re: Random lean condition after shift to third gear

Post by D-Rob »

May I email it instead of posting?
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Random lean condition after shift to third gear

Post by Hondata »

Hondata
D-Rob
Posts: 67
Joined: Tue Apr 29, 2008 6:11 am

Re: Random lean condition after shift to third gear

Post by D-Rob »

Thank you; I have sent over the calibration and the logs.
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Random lean condition after shift to third gear

Post by Hondata »

Can you disable live tuning and re-test?
Hondata
D-Rob
Posts: 67
Joined: Tue Apr 29, 2008 6:11 am

Re: Random lean condition after shift to third gear

Post by D-Rob »

Hondata wrote:Can you disable live tuning and re-test?
Absolutely can.

Disable all live tables I currently have enabled?
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Random lean condition after shift to third gear

Post by Hondata »

Yes, disable all the live tables.
Hondata
D-Rob
Posts: 67
Joined: Tue Apr 29, 2008 6:11 am

Re: Random lean condition after shift to third gear

Post by D-Rob »

All live tuning tables disabled.

Same condition.
Attachments
NoLiveTuning_Lean3rdGear.fpdl
(30.62 KiB) Downloaded 310 times
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Random lean condition after shift to third gear

Post by Hondata »

It is lean on spool up too. Next step is to disable the secondary o2 sensor.
Hondata
D-Rob
Posts: 67
Joined: Tue Apr 29, 2008 6:11 am

Re: Random lean condition after shift to third gear

Post by D-Rob »

Hondata wrote:It is lean on spool up too. Next step is to disable the secondary o2 sensor.
Yeah, that's a new thing too since it came off the dyno.

Will give that a shot.
D-Rob
Posts: 67
Joined: Tue Apr 29, 2008 6:11 am

Re: Random lean condition after shift to third gear

Post by D-Rob »

Hondata wrote:It is lean on spool up too. Next step is to disable the secondary o2 sensor.
Just checked over that file again; the secondary O2 has been disabled the whole time.
the_wrench116
Posts: 35
Joined: Wed Mar 12, 2014 4:20 pm

Re: Random rich condition after shift to third gear

Post by the_wrench116 »

i have a 3.5 inch intake and am also sufering from a random Rich condition when im at the track 2-3 shift.
Attachments
good launch test.fpdl
launch+BOG...
(1.96 MiB) Downloaded 312 times
Post Reply