Page 1 of 2

FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Wed Oct 24, 2018 7:49 am
by D-Rob
Hello,

I have several clients that have updated calibrations using the 3.1.6.0 software and are receiving the P0128 (Coolant thermostat temperature check) DTC code despite it being disabled in the calibration for many months.

I've been explaining to said clients that they do not have a failing thermostat, and that this is a bug in the software.

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Wed Oct 24, 2018 10:20 am
by Spunkster
Can you post the calibrations that are having this issue?

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Wed Oct 24, 2018 4:32 pm
by D-Rob
I can email them, if you'd like.

support@hondata.com?

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Thu Oct 25, 2018 11:49 am
by Spunkster
please send it as soon as possible

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Mon Oct 29, 2018 12:42 pm
by D-Rob
Calibrations were sent a few days ago, by the way.

Thank you.

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Tue Nov 20, 2018 9:20 am
by D-Rob
I see no mention of a fix in 3.1.8.

Should I tell the clients the error is still not addressed?

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Fri Nov 23, 2018 2:11 pm
by D-Rob
I'd like to add that 2007 RDX also tosses P0128 when the second ECT sensor is disabled.

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Tue Nov 27, 2018 11:32 am
by Spunkster
please post the calibrations here as nothing has been received.

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Wed Nov 28, 2018 3:43 pm
by D-Rob
An email was sent to support@hondata.com on Friday, October 26th that contained four calibrations.

It has been resent just now.

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Mon Jan 28, 2019 1:32 pm
by D-Rob
Should I resent these to a different email?

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Mon Jan 28, 2019 2:11 pm
by Spunkster
Our software engineer is looking into this, but it may be a month or so before we are able to test in a vehicle.

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Wed Jun 05, 2019 4:03 pm
by ruddyrid
Any update on this? Sucks to have to clear the code so often or having to deal with it coming on. Hopefully it's a simple enough fix

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Sat Jun 22, 2019 11:06 pm
by Kevvo21
Any updates?

I've had my coolant thermostat + coolant replaced, yet P0128 still pops up after 2 cold engine start cycles. Car idles fine, coolant temps are fine, not sure exactly why I'm getting this code. I've updated to the most recent update and re-uploaded my tune. I heard disconnecting my battery for an hour might help but i doubt it.

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Mon Jun 24, 2019 9:55 am
by Hondata
What vehicle? Are you using ECT2 for an input?

Re: FP Manager version 3.1.6.0: P0128 shows up when the DTC is disabled

Posted: Mon Jun 24, 2019 3:02 pm
by Kevvo21
Hondata wrote: Mon Jun 24, 2019 9:55 am What vehicle? Are you using ECT2 for an input?
2014 civic si.
Tuner has my 'Second ECT sensor" disabled under the 'Misc' section, is that what's causing the issue?

I can disable 'Coolant Thermostat temp check (P0128) in 'Misc', but I wanted to leave that as a last resort. Since I just replaced my thermostat, I can disable that without having the worry that my thermostat was busted.

I can email you my calibration

Thanks,