Noise in rear speed sensor
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Noise in rear speed sensor
Hi,
When the engine running I'm am seeing noise in the rear wheel speeds. It is there with/without the rear sensors plugged in. I've tried moving the ground from the thermostat housing to the chassis, along with trying to shield the rear speed wires without success. The front wheel speeds work fine. I think the interference is coming in at the traction box. I have it mounted on the side of the HVAC blow behind the glove box. I also tried spark plugs with resistors.
When the engine running I'm am seeing noise in the rear wheel speeds. It is there with/without the rear sensors plugged in. I've tried moving the ground from the thermostat housing to the chassis, along with trying to shield the rear speed wires without success. The front wheel speeds work fine. I think the interference is coming in at the traction box. I have it mounted on the side of the HVAC blow behind the glove box. I also tried spark plugs with resistors.
- Attachments
-
- noiseAtIdleResistorPlugs.zip
- (12.27 KiB) Downloaded 203 times
Re: Noise in rear speed sensor
Are the wires for the sensors all twisted pairs all the way to the box?
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
Yes, I was able to use the supplied twisted pair harness.
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
Ran down the center and split near the fuel tank.
Re: Noise in rear speed sensor
IF you completely disconnect the harness form the traction control box do you still see noise with it just powered and connected via the USB?
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
No noise powered by USB with the car running. I don't have the tool to de pin the connector so that was with the connector un plugged but module in the same location.
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
Ecu is a new HAsports p28 with a new s300
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
I cut the ELD wire and the noise in the rear wheel speeds is gone. In the S300 calibration I have traction control enabled box checked on D10. On the Misc tab i have Disable ELD checked.
Re: Noise in rear speed sensor
Was the ELD still wired to it's original location or was it cut?
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
ELD was cut and ECU was wired directly to the Traction control box at pin D10. Currently with the connection to pin D10 cut there is not noise. Power is coming from IGP1 and Ground is at the thermostat.
Re: Noise in rear speed sensor
*Note that if the ELD input (D10) is used then R136 and R138 (US ECUs) may need to be removed.
Has this been done?
Has this been done?
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
Not sure. Is a new unit and I haven't pulled the cover off yet. Also I didn't see that note in the instructions.
I'll check once I get home.
I'll check once I get home.
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
I've cut 136 and 138. Not sure why but now with the ELD disconnected it still has the wheel speed noise. I've moved the power wire away from the ECM closer to battery directly and it did improve the noise with the TCS connect to D10. I need to extend wires to run directly to the battery, to see if this further improves the issue.
-
- Posts: 24
- Joined: Tue Nov 20, 2018 6:01 pm
Re: Noise in rear speed sensor
The USB light is always on or flickering even with the computer not connected. I put an oscilloscope on the power wire and nothing really stood out.
Re: Noise in rear speed sensor
Where are you connecting for power and ground?