Rev Hang

FlashPro questions & answers specific to the 2007-2008 US TSX
Post Reply
cYn
Posts: 10
Joined: Thu Dec 15, 2011 10:29 pm

Rev Hang

Post by cYn » Thu Dec 15, 2011 10:32 pm

I was wondering if the base map for the TSX (TSX-07-2-Tuned) is already calibrated to remove rev hang. I flashed that base map today and I think I'm still experiencing some rev hang. Could you confirm that the base map actually removed, or even reduced, rev hang? Thank you.

User avatar
Hondata
Site Admin
Posts: 8755
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Rev Hang

Post by Hondata » Fri Dec 16, 2011 10:16 am

Reduce the 'Overrun fuel cut delay'
Hondata

cYn
Posts: 10
Joined: Thu Dec 15, 2011 10:29 pm

Re: Rev Hang

Post by cYn » Fri Dec 16, 2011 12:55 pm

The current settings are 30 30 30 30 30

The Civic Si's settings are 60 50 40 30 30

Should I set it to the Civic Si's setting?

User avatar
Hondata
Site Admin
Posts: 8755
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Rev Hang

Post by Hondata » Sat Dec 17, 2011 9:15 am

No, reduce the values in 'Overrun fuel cut delay', not increase. eg Try 0,0,0,0,0,0 then 10,10,10,10,10,10 and 20,20,20,20,20,20 and see which works the best.
Hondata

cYn
Posts: 10
Joined: Thu Dec 15, 2011 10:29 pm

Re: Rev Hang

Post by cYn » Fri Jan 13, 2012 12:42 pm

Hondata wrote:No, reduce the values in 'Overrun fuel cut delay', not increase. eg Try 0,0,0,0,0,0 then 10,10,10,10,10,10 and 20,20,20,20,20,20 and see which works the best.
I truly apologize if I sounded a bit dumb when I asked about the Civic's setting. It's just I read some report that they don't experience rev hang so I tried to mimic a bit of their calibrations.

Also, the Overrun Fuel Cut delay doesn't go down to 0. The lowest it will go is 10. Is that just the way it's implemented or is it a bug?

User avatar
Hondata
Site Admin
Posts: 8755
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Rev Hang

Post by Hondata » Fri Jan 13, 2012 1:24 pm

Yes, 10 is as low as it will go.
Hondata

cYn
Posts: 10
Joined: Thu Dec 15, 2011 10:29 pm

Re: Rev Hang

Post by cYn » Fri Jan 13, 2012 5:07 pm

Hondata wrote:No, reduce the values in 'Overrun fuel cut delay', not increase. eg Try 0,0,0,0,0,0 then 10,10,10,10,10,10 and 20,20,20,20,20,20 and see which works the best.
I also notice something different. In the TSX calibration, there's only 5 gear columns. The TSX is a 6 speed. Is it even supposed to be like that?

Cause I notice that when you suggested me to change the Overrun values, you gave me 6 inputs. But the calibration only allows 5.

Post Reply