New cpr kit issues
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
New cpr kit issues
So straight to the point I have a turbo b16a in a 00 gsr. I have a obd2 to obd1 jumper harness. So I hooked up the kit got the coil packs in (currently have bkr7 plugs in it) and I obd1 distributor that was wired to use an obd2 connector as that is what is on the cars harness. Originally when I pinned the wires into the ecu I was getting the power light on the box and when I would crank the car the ignition light would flash but no sync light also it would only crank never sounded like it was trying to actually turn over. So I re pinned the sync wire and accidentally pulled the ign wire out of A22 of the jumper harness (the part that plugs into the ecu). I re pinned the ign wire and put it into the A22 slot went to start the car and now I had the power light and my sync light flashing but no ign light. I cleaned the ground and that didn’t work. I bought 10 new pins and a brand new jumper harness and pinned the wire into A22 and still sync power but no ign light I re pinned this wire about 9 separate time just in case and yes I was using the proper tool. I thought maybe when I was putting the connector into the ecu it was pushing the pin out so I opened the door and “held/“pushed”” the pin and went to start the car and still power sync but no ign light. Was curious if I should try A21 (I know they are the same but idk what else to do). I was thinking maybe the box I have is bad ? I hooked my laptop up and it gave an error signal along the lines of ign signal not detected. Any help or direction would be appreciated
Re: New cpr kit issues
You can try A21, as internally they are the same on the ECU.
Post a picture of the inside of the CPR box.
Post a picture of the inside of the CPR box.
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
Re: New cpr kit issues
I tried A21, and still having the same problems. Thanks.
- Attachments
-
- 5A2F1BC6-6D94-4DEE-BB6B-713F15062945.jpeg (3.02 MiB) Viewed 3320 times
Re: New cpr kit issues
What is the actual error you are getting when you datalog?
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
Re: New cpr kit issues
The actual code is 15 IGM ignition output signal. That’s in A21.
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
Re: New cpr kit issues
Sorry, A22 not A21
Re: New cpr kit issues
If you are getting this code the ECU may be the issue. I would recommend trying with a friend's ECU.
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
Re: New cpr kit issues
The car was having no issues until I put this kit on. Also, the ignition light was coming on until I accidentally pulled the wire out. I have a new harness too.
Re: New cpr kit issues
You should still try with a different ECU.
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
Re: New cpr kit issues
I will try. What are you thinking is wrong with the ecu? Just out of curiosity since it has been working until I got the CPR.
Re: New cpr kit issues
These ECU's are over 25 years old and sometimes an ECU just doesn't work well with the CPR.
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
Re: New cpr kit issues
Oh! That makes sense. Thank you.
After I try a new ecu, what are the next steps?
After I try a new ecu, what are the next steps?
Re: New cpr kit issues
first see if it works as it should with a different ECU.
-
- Posts: 14
- Joined: Wed May 12, 2021 11:09 pm
Re: New cpr kit issues
Okay, the only ecu i could find to use had the red s300. It didn’t have q32, so I took that s300 out and put y in t in mine. S-Manager is telling me that the USB device isn’t recognized.