Page 1 of 2

FlashProManager V1.3.7 (beta)

Posted: Thu Aug 23, 2012 10:09 am
by Hondata
V1.3.6 Changes
  • Added support for traction control.
  • [07 TSX] Fixed datalogging
  • [07 TSX] Added speed adjustment (dash).
  • Improved Hondata Vault behavior when searching and downloading files.
V1.3.7 Changes
  • Fixed problem recording from FlashPro.
Download here

Re: FlashProManager V1.3.4 (beta)

Posted: Thu Aug 23, 2012 11:35 am
by Nike
Hondata wrote:V1.3.4 Changes
[*][07 TSX] Added speed adjustment (dash).
When will be speed adjustment to R18? Thanks.

Re: FlashProManager V1.3.4 (beta)

Posted: Thu Aug 23, 2012 11:56 am
by Nike
Hondata wrote:Download here
Don't worked. Please, upload ver. 1.3.3

Re: FlashProManager V1.3.4 (beta)

Posted: Thu Aug 23, 2012 12:25 pm
by Hondata
What does not work?

Re: FlashProManager V1.3.4 (beta)

Posted: Thu Aug 23, 2012 12:54 pm
by Nike
Hondata wrote:What does not work?
Write: "incorrect version...tsx..tpl.."
After that don't open calibration and datalog, all windows are empty. If install ver.1.3.3 than OK.

Re: FlashProManager V1.3.4 (beta)

Posted: Thu Aug 23, 2012 1:32 pm
by Hondata
Ok, thanks, will be fixed very shortly.

Re: FlashProManager V1.3.4 (beta)

Posted: Mon Aug 27, 2012 1:38 pm
by civicRSA
[Civic CTR - Euro] Increased maximum cam angle to 50 degrees, added warm up retard table.

Still not added?

Re: FlashProManager V1.3.4 (beta)

Posted: Mon Aug 27, 2012 3:33 pm
by Hondata
Should be there in the tables window under 'Water temperature ignition retard'.

Re: FlashProManager V1.3.4 (beta)

Posted: Tue Aug 28, 2012 12:51 pm
by civicRSA
Hondata wrote:Should be there in the tables window under 'Water temperature ignition retard'.
Not there at all or I am blind.
There is only coolant temp HOT retard

Re: FlashProManager V1.3.4 (beta)

Posted: Tue Aug 28, 2012 1:48 pm
by Spunkster
We will recompile and upload the software again and you should see it then.

Re: FlashProManager V1.3.4 (beta)

Posted: Tue Aug 28, 2012 2:10 pm
by Nike
Spunkster wrote:We will recompile and upload the software again and you should see it then.
All OK)
When you will be speed adjustment to R18? Thanks.

Re: FlashProManager V1.3.4 (beta)

Posted: Thu Aug 30, 2012 11:02 am
by civicRSA
Traction control is not available on Civic Type-R AFM calibrations.
Is there a reason for this?

What is the voltage range of the traction control ecu output?
Anything below 1v on the ELD and ECT2 inputs does not register. Had this problem when using these inputs for a wideband.

Re: FlashProManager V1.3.4 (beta)

Posted: Thu Aug 30, 2012 8:45 pm
by Hondata
It is available for the Euro CTR - wait for the release tomorrow.

The over slip = (input voltage - 1V) * 10% per volt, so it is offset by 1V to avoid offset problems at low voltages.

Re: FlashProManager V1.3.4 (beta)

Posted: Fri Aug 31, 2012 2:01 am
by tu5j4
Is it possible to make the VTC storingcodes completely removable with flashpro? I had some P and U storingcodes after losing powersteering control and wasn`t able to correct that with flashpro, eventhough there`s VTC clear instructions.
Had to transport my FN2 to the dealer so they could eliminate the codes with their special computerstuff. What a work and the amount of time and money I lost to that.
Also this caused me to lose faith in flaspro when it comes to relliability.

Re: FlashProManager V1.3.4 (beta)

Posted: Fri Aug 31, 2012 8:08 am
by Hondata
You probably mean DTCs or error codes.

Multiple devices are connected to the data bus in the car, and they all can generate error codes. eg ECU, EPS, ABS, VSA, air bags, dash, etc

Only the ECU error codes can be cleared with FlashPro, generally starting with 'P' (for powertrain).