k20z2

FlashPro Manager software
Post Reply
yeuror
Posts: 3
Joined: Thu Dec 31, 2009 10:10 am

k20z2

Post by yeuror » Wed Aug 11, 2010 7:39 am

what about this engine type? is available the flash pro or anything else about programming?

User avatar
Spunkster
Site Admin
Posts: 18059
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Post by Spunkster » Wed Aug 11, 2010 9:49 am

What vehicle is this and what is the ECU code?

ajpturbopittsburgh
Posts: 145
Joined: Wed May 26, 2010 10:58 am

Post by ajpturbopittsburgh » Wed Aug 11, 2010 3:37 pm

K20Z2
Found in:
2006- Acura CSX (Canada)
Displacement: 1,998 cc (121.9 cu in)
Compression: 9.6:1
Power: 155 hp (114 kW) @ 6000 rpm (SAE net J1349 Rev 8/04)
Torque: 139 ft·lbf (188 N·m) @ 4500 rpm
Redline: 6800 rpm


2006- Honda Civic (JDM)
Displacement: 1,998 cc (121.9 cu in)
Compression: 9.6:1
Power: 155 hp (114 kW) @ 6000 rpm
Torque: 139 ft·lbf (188 N·m) @ 4500 rpm
Redline: 6800 rpm


2006- Honda Accord(Europe)
Displacement: 1998 cc
Compression: 9.6:1
Power: 155 hp (114 kW) @ 6000 rpm
Torque: 139 ft·lbf (188 N·m) @ 4500 rpm
Redline: 6800 rpm

User avatar
Spunkster
Site Admin
Posts: 18059
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Post by Spunkster » Wed Aug 11, 2010 3:43 pm


m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy » Mon Feb 12, 2018 10:13 am

Can i run a turbo setup on this engine with a PRA ecu

User avatar
Spunkster
Site Admin
Posts: 18059
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: k20z2

Post by Spunkster » Mon Feb 12, 2018 10:33 am

What vehicle is this in?

m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy » Mon Feb 12, 2018 12:11 pm

Spunkster its hopefully going in a mazda rx8

User avatar
Spunkster
Site Admin
Posts: 18059
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: k20z2

Post by Spunkster » Mon Feb 12, 2018 12:40 pm

Is this drive by wire?

m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy » Mon Feb 12, 2018 1:45 pm

I think it is but haven't checked yet. there are a couple of guys from Poland that have done it with the k20z4 just one is using hondata and the other is using an emu engine management system. however my polish is no good so I was looking for a pin out for a PRA ecu as I can only find picture upon picture for US compatible ecus

User avatar
Spunkster
Site Admin
Posts: 18059
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: k20z2

Post by Spunkster » Mon Feb 12, 2018 5:48 pm

IF it is drive by wire we do not offer anything that will work with that in an engine swap.

m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy » Tue Feb 13, 2018 2:32 am

all im looking for is a pin out for the pra ecu

Post Reply