problem with jrsc

FlashPro questions & answers specific to the FN2 European Civic Type R
Post Reply
partizano
Posts: 7
Joined: Tue Apr 09, 2019 6:58 am

problem with jrsc

Post by partizano »

Engine stock + jrsc. There is a problem with afr on WOT. The beginning is rich, then AFR goes to 14.4-14.5 for boost. No AFM, only MAP. Other basemap with AFM this same situation.
Where to look for a problem?

Time 0:27 - 0:28
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: problem with jrsc

Post by Hondata »

Have you relocated the MAP sensor so that it can see boost?
Hondata
partizano
Posts: 7
Joined: Tue Apr 09, 2019 6:58 am

Re: problem with jrsc

Post by partizano »

Flashpro manager displays boost
User avatar
R-12914
Posts: 349
Joined: Sun Dec 01, 2013 12:13 pm
Location: Germany/Bavaria

Re: problem with jrsc

Post by R-12914 »

Can you post a datalog, please!
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
partizano
Posts: 7
Joined: Tue Apr 09, 2019 6:58 am

Re: problem with jrsc

Post by partizano »

startnew.fpdl
(664.45 KiB) Downloaded 185 times
startnew.fpcal
(17.45 KiB) Downloaded 205 times
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: problem with jrsc

Post by Hondata »

The fuel tables are a mess. Only the 0 degree table has been altered, and then in a bad way.
Hondata
partizano
Posts: 7
Joined: Tue Apr 09, 2019 6:58 am

Re: problem with jrsc

Post by partizano »

Yes, it's for the test, but increasing the fuel has no afr change in the boost around 0.3bar or more
User avatar
Spunkster
Site Admin
Posts: 22741
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: problem with jrsc

Post by Spunkster »

Check your fuel pressure as it looks like it may be dropping.
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: problem with jrsc

Post by Hondata »

I'm fairly sure you're only changing the 0 degree table, not all of them.
Hondata
partizano
Posts: 7
Joined: Tue Apr 09, 2019 6:58 am

Re: problem with jrsc

Post by partizano »

Yes, but all cells in vtc low cam are set to 0
partizano
Posts: 7
Joined: Tue Apr 09, 2019 6:58 am

Re: problem with jrsc

Post by partizano »

fuel pressure 3,2-3,3bar hi-load, low load 3.5

each vtc setting (15 *, 30 *, 40 *) is the same. About 0.3 bar arf increases
partizano
Posts: 7
Joined: Tue Apr 09, 2019 6:58 am

Re: problem with jrsc

Post by partizano »

problem solved, o2 sensor damaged, the external sensor 02 displays the actual values on all vtc and boost
Post Reply