Launch Control

FlashPro questions & answers specific to the 2006-2011 Americas Civic Si
Locked
ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Launch Control

Post by ImAuthenticFTW » Wed Jun 17, 2009 6:45 pm

just curious on how it is going to act with the FlashPro, will it be like the 5500 stock limiter just adjustable? maybe the 8200 rev llimiter? more of a stutter step? and would it be possible for you guys to implement a cut off speed like the KPro does? and even an ignition cut launch control/anti lag for turbo'd people?

User avatar
Hondata
Site Admin
Posts: 8774
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Post by Hondata » Thu Jun 18, 2009 8:01 am

Yes, it is similar to KPro, with an adjustable launch limiter. I believe the cutoff speed is 5 kph / 3 mph - that should work without adjustment.
Hondata

ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Post by ImAuthenticFTW » Thu Jun 18, 2009 11:01 am

i know its adjustable, i was curious on how it is going to behave though, will it act like the 5500rpm limiter with a "slow" stutter, or the rev limiter which is a quicker stutter so to speak

User avatar
Hondata
Site Admin
Posts: 8774
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Post by Hondata » Fri Jun 19, 2009 7:31 am

It is slightly quicker acting than stock.
Hondata

ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Post by ImAuthenticFTW » Thu Jul 02, 2009 6:57 pm

Hondata wrote:Yes, it is similar to KPro, with an adjustable launch limiter. I believe the cutoff speed is 5 kph / 3 mph - that should work without adjustment.
Hate to bump this, but i just wanted to share some finding on this. I tried to find out at which speed the LC limiter stops and becomes the real rev limiter. Well on my car as soon as i move it revs to 8600. My speedo didnt even say 1mph and it reved out to 8600. I think you guys should allow the cut off speed to be end user adjustable please

User avatar
Hondata
Site Admin
Posts: 8774
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Post by Hondata » Tue Jul 07, 2009 7:32 am

5 km/h
Hondata

ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Post by ImAuthenticFTW » Tue Jul 07, 2009 9:37 am

not on my car, like i said before i went and tested this, my car moved slightly, to the point where it was rolling but the speedo still said 0, and the revs went all the way to 8600rpms..... ill try to make a datalog of this for you today

ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Post by ImAuthenticFTW » Tue Jul 07, 2009 7:36 pm

Ok so i did a datalog for you guys, what i did was find a hill that would allow my car to roll slightly, but not gain speed to fast. I set my foot on the brake and his the Launch Limiter, i then lifted my foot off the brake. As you can see on the datalog when i hit 2mph, or 3.2Km/H the rev were already at ~7000RPMS.
Attachments
2step problem.fpdl
(1.17 MiB) Downloaded 104 times

User avatar
Hondata
Site Admin
Posts: 8774
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Post by Hondata » Wed Jul 08, 2009 7:15 am

What calibration are you using?
Hondata

ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Post by ImAuthenticFTW » Wed Jul 08, 2009 9:07 am

K&N V2 SRI, raceheader.... MAP based calibration.

also please note that my throttle wasnt even 100% and it climbed that high in the rev range, had it been at 100% throttle i would have been bouncing off the limiter before 2mph...

ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Post by ImAuthenticFTW » Mon Jul 13, 2009 8:12 am

anything?

User avatar
Hondata
Site Admin
Posts: 8774
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Post by Hondata » Mon Jul 13, 2009 11:45 am

I've tested it and it is about 1 km/h
Hondata

ImAuthenticFTW
Posts: 78
Joined: Fri May 08, 2009 12:59 pm

Post by ImAuthenticFTW » Mon Jul 13, 2009 12:20 pm

okay, but is it possible to enable end user controlled cut offs?? 1km/h is no where near enough IMHO to gain traction

mattminer
Posts: 13
Joined: Wed Aug 05, 2009 7:14 am

Post by mattminer » Wed Aug 05, 2009 7:18 am

the lack of adjustability in flashpro has been disappointing so far. I really hope more tables get opened up soon, this being one of them.

Locked