Page 1 of 1

all motor b16a calibration in need!!

Posted: Wed Feb 11, 2015 9:31 am
by mitchb16a
Iv got a freshley rebuilt b16a with 17, 000km on it. Has a header back 2.5inch magnaflow exhaust, password jdm intake, a set of 2001 USDM ITR cams and springs. Stock Iinjectors. Using a jdm b16 basemap right now but I feel like a little more could be pushed out of it. Runs a bit rich I fined but thats the least of my worries.New to thd Hondata system and dont want to screw something up on my build. All help Iis appriciated!!

Re: all motor b16a calibration in need!!

Posted: Fri Apr 17, 2015 7:13 pm
by cam6222
I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
The attachment Wfb8922 16a.skl is no longer available

Re: all motor b16a calibration in need!!

Posted: Thu Apr 23, 2015 12:36 am
by Monnoracing
only tune I have that has your setup. This car ran good with this tune

Re: all motor b16a calibration in need!!

Posted: Wed May 06, 2015 8:18 pm
by Kevinbrahh
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
Wfb8922 16a.skl
Hi do you have basemap for Injen CAI with 421 headers and 2.5 exhaust? I am doing an engine build soon so I don't want to tune my car yet. Thank you!!!

Re: all motor b16a calibration in need!!

Posted: Thu Jun 11, 2015 2:49 am
by cam6222
Kevinbrahh wrote:
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.
The attachment Wfb8922 16a.skl is no longer available
Hi do you have basemap for Injen CAI with 421 headers and 2.5 exhaust? I am doing an engine build soon so I don't want to tune my car yet. Thank you.

Look for this attachment
PDG45.skl
(40.05 KiB) Downloaded 384 times

Re: all motor b16a calibration in need!!

Posted: Fri Nov 25, 2016 12:02 am
by ecronic
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.

Wfb8922 16a.skl
I know this is a very old thread but could really use your help.

I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.

Please suggest the best possible basemap you have that matches to the mods below:

B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.

Hope to hear from you soon.

Thanks & regards
Dev

Re: all motor b16a calibration in need!!

Posted: Thu Dec 08, 2016 9:03 am
by Zperformance
ecronic wrote:
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.

Wfb8922 16a.skl
I know this is a very old thread but could really use your help.

I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.

Please suggest the best possible basemap you have that matches to the mods below:

B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.

Hope to hear from you soon.

Thanks & regards
Dev
Hey Dev, you should be able to run your car with a hondata s300 basemap (b16/p30 map). Since you only have minor mods it should be capable to run your car.

Re: all motor b16a calibration in need!!

Posted: Thu Dec 08, 2016 9:22 am
by ecronic
Zperformance wrote:
ecronic wrote:
cam6222 wrote:I have several calibration since i also using b16a. maybe this may help u and u just do some touchup.

Wfb8922 16a.skl
I know this is a very old thread but could really use your help.

I've got a B16A6 SIR that had a P30 ECU that I sold recently. I've got a S300 ECU but no basemap and the car is just parked now.

Please suggest the best possible basemap you have that matches to the mods below:

B16A6 on stock internals, skunk2 1st gen intake, edelbrok tb, Spoon 1st gen headers & 2.5" exhaust.

Hope to hear from you soon.

Thanks & regards
Dev
Hey Dev, you should be able to run your car with a hondata s300 basemap (b16/p30 map). Since you only have minor mods it should be capable to run your car.
Hi Zperformance

Thanks for replying. I'm just worried about running lean or rich. I've got afr gauge installed so guess I'm going to go ahead with that map and post the result. Let's hope someone can help out then setting up the fuel tables.

Cheers
Dev

Re: all motor b16a calibration in need!!

Posted: Sat Dec 10, 2016 2:53 pm
by Zperformance
Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.

Re: all motor b16a calibration in need!!

Posted: Sat Dec 10, 2016 7:53 pm
by ecronic
Zperformance wrote:Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.
Okay so I tried the s300 cal for b16a/ p30 & the check engine light came on. Errors that shoot up are oxygen sensor heater & knock sensor. My stock ecu doesn't have any errors.

Fyi
Stock ecu: P30 & s300 ecu: p28

Appreciate you replying my posts Zperformance and thanks to anyone who can some light on this.

Cheers
Dev

Re: all motor b16a calibration in need!!

Posted: Wed Dec 14, 2016 10:11 am
by Zperformance
ecronic wrote:
Zperformance wrote:Just adjust fuel map slightly to be safe enough. You would always want afr to be slightly richer then lean.
Okay so I tried the s300 cal for b16a/ p30 & the check engine light came on. Errors that shoot up are oxygen sensor heater & knock sensor. My stock ecu doesn't have any errors.

Fyi
Stock ecu: P30 & s300 ecu: p28

Appreciate you replying my posts Zperformance and thanks to anyone who can some light on this.

Cheers
Dev
Go through the paramateres and you can disable it. If you are not sure, let me know i will disable them and upload it here for you.

Re: all motor b16a calibration in need!!

Posted: Wed Dec 14, 2016 10:24 am
by Zperformance
basically P30 basemap i just disable the sensors