Page 1 of 2
Hondata s300 red led flashing fast
Posted: Sat Apr 29, 2017 3:24 am
by jose_mbk
My English is bad, I will use a translator. Install my honda s300 v3 in my Honda Prelude SH. Smanager does not read the engine parameters in real time. A red light flashes quickly, not before. When I connect to the PC without connecting to the vehicle also red light that blinks. What can be the motive?
Re: Hondata s300 red led flashing fast
Posted: Sun Apr 30, 2017 9:48 am
by jose_mbk
The red light no longer appears but if I have the revolutions limited to 2500rpm. I have inspected the harness and it looks like it is perfect. The welds are perfect. I cut the j12. J4 I have not cut it because I read that it is not relevant. So I do not know what to do anymore.
Re: Hondata s300 red led flashing fast
Posted: Mon May 01, 2017 9:42 am
by Spunkster
Is this in a rectangular ECU or a square ECU?
Re: Hondata s300 red led flashing fast
Posted: Mon May 01, 2017 4:30 pm
by jose_mbk
37820-p28-g02 AWR
Is rectangular
Re: Hondata s300 red led flashing fast
Posted: Mon May 01, 2017 4:42 pm
by Spunkster
Have you enabled on-board datalogging?
Re: Hondata s300 red led flashing fast
Posted: Mon May 01, 2017 4:47 pm
by jose_mbk
I'll check in a moment
Re: Hondata s300 red led flashing fast
Posted: Mon May 01, 2017 4:57 pm
by jose_mbk
Is not activated. The light only blinks when I connect the pc, I suppose that's why. My problem now is that it does not rise from 2500rpm and in idle it goes off
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 9:04 am
by Spunkster
so you are saying the red light stops flashing when it idles?
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 10:55 am
by jose_mbk
The red light blinks only when the PC is connected. Now I have the problem of protection mode
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 11:25 am
by Spunkster
What is the serial number that is on the s300 board inside the ECU?
From Help, About, what is the version of software you are using?
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 11:50 am
by jose_mbk
Serial number Hondata: 39248
Serial number ECU: 37820-p28-g02
Hardware: version 3
Firmware: version 8
Software: version 2.5.5
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 12:21 pm
by Spunkster
Have you uploaded the calibration to the ECU using this version of software? Are you able to datalog?
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 12:36 pm
by jose_mbk
I have uploaded the calibration with this version on two different PCs. I can not do datalog because it does not read the sensors. Even if it starts, it's strange
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 3:43 pm
by Spunkster
Has the s300 ever worked on this ECU?
Where are you located?
Re: Hondata s300 red led flashing fast
Posted: Tue May 02, 2017 3:52 pm
by jose_mbk
I dont understand that question. I live in Cadiz, Spain