Car wont idle correctly while moving
-
- Posts: 11
- Joined: Mon Aug 01, 2011 8:12 am
Car wont idle correctly while moving
s300v2
b18c turbo
1000cc ID
IACV duty cycle in the middle @ normal
In the IDLE parameters i have my moving minimum idle set to 1500rpm but it does not work.
also if i adjust idle while stationary and upload nothing happens.
ive attached datalog recording
update: attached calibration
b18c turbo
1000cc ID
IACV duty cycle in the middle @ normal
In the IDLE parameters i have my moving minimum idle set to 1500rpm but it does not work.
also if i adjust idle while stationary and upload nothing happens.
ive attached datalog recording
update: attached calibration
- Attachments
-
- STOUT.skl
- (44.13 KiB) Downloaded 131 times
-
- Datalog-170211-153003.s3d
- (108.05 KiB) Downloaded 134 times
Last edited by chrisbogart on Wed Feb 15, 2017 10:50 pm, edited 1 time in total.
Re: Car wont idle correctly while moving
You have not posted the calibration that the datalog was made with.
-
- Posts: 11
- Joined: Mon Aug 01, 2011 8:12 am
Re: Car wont idle correctly while moving
uploaded calibration
also, you can see in the datalog that when i let off throttle to coast, my fuel duty cycle goes to 0% and almost dies.
also, you can see in the datalog that when i let off throttle to coast, my fuel duty cycle goes to 0% and almost dies.
Re: Car wont idle correctly while moving
I don't actually see a problem in that datalog. The fuel injectors are supposed to shut off during deceleration, so that is normal. Have you set the idle per the factory service manual instructions?
-
- Posts: 11
- Joined: Mon Aug 01, 2011 8:12 am
Re: Car wont idle correctly while moving
my idle adjustment screw is almost closed.
i dont understand why the minum moving idle drops below where its supposed to and never corrects
i didnt decel in gear, i simply put the clutch in then the rpms drop too low and duty cyle goes to 0% from 6.8 seconds on datalog to 7.3
i dont understand why the minum moving idle drops below where its supposed to and never corrects
i didnt decel in gear, i simply put the clutch in then the rpms drop too low and duty cyle goes to 0% from 6.8 seconds on datalog to 7.3
Re: Car wont idle correctly while moving
With the car fully warmed up and idling, unplug the idle control connector and see what RPM it idles at.
-
- Posts: 11
- Joined: Mon Aug 01, 2011 8:12 am
Re: Car wont idle correctly while moving
what will this determine? if my IACV is working or not?
Re: Car wont idle correctly while moving
To see if it is adjusted properly.
-
- Posts: 11
- Joined: Mon Aug 01, 2011 8:12 am
Re: Car wont idle correctly while moving
So idle is adjusted properly. but the s300 still wont change idle and doesnt catch a falling idle when pushing clutch in.
Re: Car wont idle correctly while moving
with the IACV disconnected, what does it idle at?
-
- Posts: 135
- Joined: Mon May 12, 2014 4:13 pm
- Location: Victoria BC
- Contact:
Re: Car wont idle correctly while moving
chrisbogart, please tell us the idle RPM while the IACV plug is disconnected, don't answer with the idle is set right, if the screw is almost fully closed I guarantee it isn't set right. Please view http://www.hondata.com/help/smanager/se ... espeed.htm to better understand the reason for our question about he RPM value.
Let's not make assumptions, please leave as much detail as possible!
-
- Posts: 135
- Joined: Mon May 12, 2014 4:13 pm
- Location: Victoria BC
- Contact:
Re: Car wont idle correctly while moving
if the idle isn't correct when adjusting the set screw, while the IACV is disconnected, there is a high probability of a vacuum leak.
Let's not make assumptions, please leave as much detail as possible!