P0132 error code
-
- Posts: 140
- Joined: Fri Jan 25, 2008 4:38 am
P0132 error code
Hello i'm tuning a K20 itr swaped car and this code is not going away.
Normally I delete this code by enable Narrowband (secondary oxygen sensor) - PRA on closed loop operation options, BUT on these case i'm using a V4 Kpro and i'm using the funtion External wideband -Kpro Input (V4 only).
How can I manage to get rid of these code?
Normally I delete this code by enable Narrowband (secondary oxygen sensor) - PRA on closed loop operation options, BUT on these case i'm using a V4 Kpro and i'm using the funtion External wideband -Kpro Input (V4 only).
How can I manage to get rid of these code?
Those who know don't tell, and those who tell don't know.
Re: P0132 error code
I get exactly the same P0132 on my newly bought EG6 with K20A2, KPro v3 in PRA ecu. Autometer 6171 wideband is connected on E15 ELD pin, no primary or secondary O2 sensors installed.Kmanager 4.1.5
O2 voltage (in sensors section) shows 4.08-4.10 Volts.
P0132 appears 115 seconds after ignition on.
Can't get rid of P0132.
Give a newbie any update please )
O2 voltage (in sensors section) shows 4.08-4.10 Volts.
P0132 appears 115 seconds after ignition on.
Can't get rid of P0132.
Give a newbie any update please )
Re: P0132 error code
Tsuchinoko: You'll have to tell us more information - the calibration would be good. PRB calibrations should not get P0132 errors so are you using a PRA calibration?
sam_eg4: You can't run in closed loop from the Autometer, so either you'll have to disabled the o2 sensors completely and run in open loop, add the factory o2 sensor or use the wideband's narrowband output (if the Autometer supports it). Again, the calibration would be good.
sam_eg4: You can't run in closed loop from the Autometer, so either you'll have to disabled the o2 sensors completely and run in open loop, add the factory o2 sensor or use the wideband's narrowband output (if the Autometer supports it). Again, the calibration would be good.
Hondata
Re: P0132 error code
Yes, I run in open loop, I have closed loop operations disabled & I have P0132.
-
- Posts: 140
- Joined: Fri Jan 25, 2008 4:38 am
Re: P0132 error code
It's a PRA ecu and is a PRA calibration.
Those who know don't tell, and those who tell don't know.
-
- Posts: 140
- Joined: Fri Jan 25, 2008 4:38 am
Re: P0132 error code
Here you have, many thanks.
- Attachments
-
- ITR DC2.2 15.9.5.kal
- (166.26 KiB) Downloaded 235 times
Those who know don't tell, and those who tell don't know.
Re: P0132 error code
Thanks for the calibrations. We'll remove that error from the next release when in open loop.
Hondata
Re: P0132 error code
Solved. :) Grounded A6 pin via 40kOhm resistor.
-
- Posts: 4
- Joined: Sat Aug 29, 2020 3:03 pm
Re: P0132 error code
hello and sorry to bring that post back.I have a eg9 k-swap with pra ecu and k20a2 uk ep3 engine but when i enable the close loop with the primary narrowband sensor i always take the error p0132 and error on heater circuit malfuction.
The car is tuned in open loop with pra calibration and the harness is fixed like tha diagram for pra ecu from hondata is any idea to help to fix this
Any help will preciate
The car is tuned in open loop with pra calibration and the harness is fixed like tha diagram for pra ecu from hondata is any idea to help to fix this
Any help will preciate
Re: P0132 error code
What diagram are you referring to?
-
- Posts: 4
- Joined: Sat Aug 29, 2020 3:03 pm
Re: P0132 error code
I have make the connections for narroband sensors like this link https://www.hondata.com/tech-euro-ctr-o2-wiring
But still i take errors like p0132 and heater circuit malfunction for primary o2 in close loop
But still i take errors like p0132 and heater circuit malfunction for primary o2 in close loop
Re: P0132 error code
That wiring is for an OEM wideband sensor and you are trying to use a narrow band sensor. This will not work.
-
- Posts: 4
- Joined: Sat Aug 29, 2020 3:03 pm
Re: P0132 error code
On the first diagram is for pra with oem narrowband sensor