TPS Reading 100%

K-Series Programmable ECU installation questions / support issues
Post Reply
Johnr051
Posts: 14
Joined: Sat Oct 10, 2020 11:07 pm

TPS Reading 100%

Post by Johnr051 »

When looking over the data log it shows my TPS running 100% when closed?? im assuming i may have switched the map and tps plugs by accident, is there a possibility my map sensor fried out????
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: TPS Reading 100%

Post by Spunkster »

You will have to verify they are plugged in correctly and then make sure you calibrate the TPS properly as well.
Johnr051
Posts: 14
Joined: Sat Oct 10, 2020 11:07 pm

Re: TPS Reading 100%

Post by Johnr051 »

I fixed the wiring now the tps is calibrated but the car won’t start, it just back fires on the intake. I’m attaching a picture of the sensors and data log also my base map just incase
Attachments
K24A_ID1000_4bar.kal
Base map
(165.29 KiB) Downloaded 96 times
56696F29-7618-4DB6-9464-E3005A9D0431.jpeg
56696F29-7618-4DB6-9464-E3005A9D0431.jpeg (4.45 MiB) Viewed 1464 times
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: TPS Reading 100%

Post by Spunkster »

Post a datalog of it trying to start
Johnr051
Posts: 14
Joined: Sat Oct 10, 2020 11:07 pm

Re: TPS Reading 100%

Post by Johnr051 »

i sent it
Attachments
kpro saves.kdl
(62.1 KiB) Downloaded 78 times
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: TPS Reading 100%

Post by Spunkster »

The TPS does not appear to be calibrated correctly as it is at 9% when trying to start and should be at zero.
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: TPS Reading 100%

Post by Hondata »

The MAP is reading 22 kPA cranking - it should be around 100 kPa. So either the MAP is bad or the calibration setting is wrong.
Hondata
Johnr051
Posts: 14
Joined: Sat Oct 10, 2020 11:07 pm

Re: TPS Reading 100%

Post by Johnr051 »

I calibrated the tps to 0.5 closed, car fires up better but it doesn't completely starts. I'm sending the datalog of it trying to start with the calibrated tps
Attachments
save 2.kdl
(282.48 KiB) Downloaded 90 times
Johnr051
Posts: 14
Joined: Sat Oct 10, 2020 11:07 pm

Re: TPS Reading 100%

Post by Johnr051 »

Hondata wrote: Wed Jan 06, 2021 5:57 pm The MAP is reading 22 kPA cranking - it should be around 100 kPa. So either the MAP is bad or the calibration setting is wrong.
how can i calibrate it on the kmanager also how can i test if its gone bad its a new 4bar map
User avatar
Hondata
Site Admin
Posts: 10434
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: TPS Reading 100%

Post by Hondata »

The MAP stays at 22 kPA no matter what else happens so it is either the wiring or MAP sensor. If you switched the TPS and MAP then the MAP probably is toast. Another silent curse that Honda used different plugs for everything in the vehicle apart from the two connectors next to each other.
Hondata
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: TPS Reading 100%

Post by Spunkster »

Also note that if a MAP sensor is wired incorrectly even for a split second it will damage the MAP sensor and it will have to be replaced.

Details on calibrating the TPS can be found at: http://www.hondata.com/help/kmanager/th ... ghtsub=tps
Johnr051
Posts: 14
Joined: Sat Oct 10, 2020 11:07 pm

Re: TPS Reading 100%

Post by Johnr051 »

Hondata wrote: Thu Jan 07, 2021 4:44 pm The MAP stays at 22 kPA no matter what else happens so it is either the wiring or MAP sensor. If you switched the TPS and MAP then the MAP probably is toast. Another silent curse that Honda used different plugs for everything in the vehicle apart from the two connectors next to each other.
I understand but before my car was starting with the same wire set up and 4 bar, I replaced the trans and fixed the tps and it doesn’t want to start completely also I tried my stock map sensor and calibrated it to match it and it still didn’t start up completely
Post Reply