Search found 136 matches
- Fri May 21, 2010 8:07 am
- Forum: s300 / SManager
- Topic: D10 ELD
- Replies: 74
- Views: 50037
D10
My factory OBD2B A plug doesn't have a wire going into slot A30, so I am under the impression I have to insert a pin into A30 and connect the wideband analog wire to that?? Is there a link or blown up image I can check to see the exact location of R136 and R138 so I will have to cut them??
- Thu May 20, 2010 5:18 pm
- Forum: s300 / SManager
- Topic: Wideband readings
- Replies: 4
- Views: 2618
Wideband readings
I have the Hondata P28 prepared ECU with the OBD2B conversion built in...I am using the NGK AFX wideband and I am currently wired into the factory O2 sensor wire on my OBD2B wiring harness and I am getting incorrect readings....Pin D14(OBD1, Primary O2 ) connects to Pin C16 ( OBD2B, Primary O2)...I ...
- Thu May 20, 2010 4:31 pm
- Forum: s300 / SManager
- Topic: D10 ELD
- Replies: 74
- Views: 50037
Wideband reading
I am having the same issue, I have a Hondata P28 ECU with a built in OBD2B conversion.....What Pin on the OBD2B harness runs into Pin D10 on the OBD1 ECU???
- Sat May 15, 2010 6:22 am
- Forum: s300 / SManager
- Topic: Hondata MAC PWM Solenoid
- Replies: 1
- Views: 1164
Hondata MAC PWM Solenoid
I have the Hondata MAC PWM Boost control soleniod....Is is normally open or normally closed? How can I check to see if its working using the Smanager program? Do I look at the Sensors list when datalogging to see if the PWM section %'s are moving??
- Sat May 15, 2010 6:12 am
- Forum: S300 Calibrations
- Topic: H22A 15 psi 1000cc injectors
- Replies: 24
- Views: 63306
yess
Yeah, me too....I'd love to have a look at that map.....
- Thu May 13, 2010 10:02 am
- Forum: s300 / SManager
- Topic: Wideband / ECU AFR readings innacurate???
- Replies: 7
- Views: 3657
hey
Yeah I just figured it out....I was adjusting the Voltage offset, BUT I forgot to click upload to ECU so nothing was happenning...I have it set perfectly now...both guage and ECU are reading the same, thanks...
- Thu May 13, 2010 6:10 am
- Forum: s300 / SManager
- Topic: Wideband / ECU AFR readings innacurate???
- Replies: 7
- Views: 3657
Wideband / ECU AFR readings innacurate???
I just installed my new NGK AFX , Fisrt off, I did it exactly as the manuel said, the yellow analog wire goes to ( in my case ) the factory O2 ( white C16 ) wire on my OBD2B harness, the brown wire is supposed to go to a ground....At first I wired the brown wire directly to the Neg battery terminal ...
- Mon May 10, 2010 1:12 pm
- Forum: s300 / SManager
- Topic: PWM Boost control Wiring
- Replies: 2
- Views: 3086
thanks
Thanks, thats exactly what I did, I used a pin from an old conversion harness...added it to my existing harness and ran the wire to the PWM Boost control solenoid....The Plug fit fine into the ECU so I am hoping it worked...thanks....
- Sun May 09, 2010 6:50 pm
- Forum: s300 / SManager
- Topic: PWM Boost control Wiring
- Replies: 2
- Views: 3086
PWM Boost control Wiring
I have a 2000 canadian civic SI with a fully built H22 turbo setup with a brand new Hondata prepared P28 ECU with an S300 installed with a built in OBD2B Conversion Plug...I just installed my Hondata electronic boost control solenoid....my harness is OBD2B and it sais on the smanager help section to...
- Sun May 09, 2010 3:03 pm
- Forum: S300 Calibrations
- Topic: H22A 15 psi 1000cc injectors
- Replies: 24
- Views: 63306
hey cardinal
Hey cardinal....Do you have MSN?? I just used the map you posted to get my car started and it worked fine....What do you have done to your car since that first map was posted in this section?? Message me....My setup is almost identical to yours.....
- Fri Apr 30, 2010 11:03 am
- Forum: s300 / SManager
- Topic: AEM Wideband through D10 ELD
- Replies: 27
- Views: 22109
Found it!!
Its was C16- primary O2 sensor wire ( White ) on my OBD2B harness
- Thu Apr 29, 2010 5:45 pm
- Forum: s300 / SManager
- Topic: AEM Wideband through D10 ELD
- Replies: 27
- Views: 22109
Thanks
Ok so according to the OBD1 ECU connector diagram from the help section link you posted, pin D14 is the O2 input, but my harness is OBD2B, so I am having a hard time figuring out what wire on my harness male plug to wire my wideband analog input into...The factory OBD2B ECU has a blank D connector, ...
- Thu Apr 29, 2010 1:11 pm
- Forum: s300 / SManager
- Topic: AEM Wideband through D10 ELD
- Replies: 27
- Views: 22109
Wideband Install
My Tuning guy wants to tune my car in open loop only, and not use the factory O2sensor, my car is a 2000Civic SI OBD2B , and I have a brand new Hondata P28ECU with the OBD2B Connector built in, so I have to wire the wideband analog wire into factory O2 sensor wire in the wiring harness.....I am havi...
- Thu Nov 12, 2009 11:01 am
- Forum: S300 Calibrations
- Topic: H22A 15 psi 1000cc injectors
- Replies: 24
- Views: 63306
H22 Calibration help
yeah I totally understand, I had an issue on the dyno with the ECtune software, I bought the whole moates demon ECtune package late Sept, and I was at the dyno shop, car strapped down, and the software on the laptop wouldn't work, turns out the guy who created it, was supposed to send me an update a...
- Thu Nov 12, 2009 5:59 am
- Forum: S300 Calibrations
- Topic: H22A 15 psi 1000cc injectors
- Replies: 24
- Views: 63306
Thanks
Thanks for the response, yeah I have a walbro 255 fuel pump and an AEM Wideband hooked up, but nut yet wired into the ECU, thats one of the next steps I have to do....The guy here that tuned my car has the base pressure set at 40PSI fuel pressure, is that too low?