Hondata

I was told that I could sent the S200 back under the same RMA number to be looked at again. I will be doing this, however, I am going to try something else first. I have a couple different S200 units on the way that I am going to try out first. If they will not connect either, then there would be no...

Got the ecu / blue box back today. I did not get an invoice or any papers / description with the package which disappointed me to say the least. Upon calling, I was told that the S200 performed fine and that the problem was the ecu. They swapped out my datalogging header and supposedly added more so...

I am running the stock ITR map on my car. It is running beautifully except for the idle... On startup it idles at 2k rpm and slowly drops. However, If I drive the car some and come to a stop, the idle oscilates up and down inbetween ~1,500 and 2,000 rpm. Reading the General Info - Idle Guide it look...

I shipped the s200 and one of my ecu's today...

Hopefully this will get taken care of.

I called and got an RMA number, but was told that I needed to send in an ecu with it... Whoever I talked to told me that there is no way to be certain that it is a faulty s200 without sending it in with a $100 diagnostic fee. If my S100 works and the S200 does not, no matter which ecu it is on, woul...

I found out that I had the interface cable plugged in backwards, so now the red led light flashes... It is not solid as it should be. My program seems to be running, however the check engine light is on and solid. There are no codes. I have tried a second ecu, and the same problem persists. Problem...

I am curious as to whether the stock 01 ITR map listed under New File is a fully tuned ITR map or an OBD2 rom dump or what..... I loaded the map, but there is a medium idle surge, and the VTEC transition is very bad. The motor all but bogs down right before VTEC. When it engages (seems just a little...

2 Parts: 1) Are the directions here (http://www.hondata.com/tech27sf512.html) correct? It seems that you change the value to 8000 only to change it back to 0 after you load the buffer? 2) Any experience using TopWin? I also have a Topwin853 and am tyring to use it as well. Didn't know if you have to...

I found out that I had the interface cable plugged in backwards, so now the red led light flashes... It is not solid as it should be.

My program seems to be running, however the check engine light is on and solid. There are no codes. I have tried a second ecu, and the same problem persists.

Since the S100 previouslly came in non boost and boost and it was not upgradable like the options for the S200, can someone post up the range of serial #'s that included boost and the ones that were not boost compatible?

Just thought this might help.

I do not have a Hondata dealer close to me.
Who here can sell me the RE4 software / USB cable and ship it to me?

Thanks,
Kevin

Topeka, KS

Is this the correct setup for Romeditor? I am a little confused on the role of the S200 unit..... Does the drawing look correct, or is the S200 unit not used anymore to do the tuning? I already installed re4 to try it out.... I opened a calibration and tried saving it, however it said the cable is n...

correct where can I get the USB cable from? Is it any different from the USB to Serial cables I already have? My laptop does not have any serial ports on it. RE4 isnt the same as SManager is it? I can't find RE4 to download anywhere, or even purchase for that matter. I do already have RE3 registered.

Spunkster wrote:This sounds like there is more going on than just an auto to manual conversion.

the ecu functioned fine for years. then all hell broke loose when I tried to tune with the S200 again. I just wanted to check and be sure that the auto to manual conversion would not be affected when cutting J1

If you do not have a zero value (jumper) across RP18 it has not been converted to manual. I would suggest doing that before cutting J1. Spunkster, do you think it would be possible to cause the motor shutting off / acting up? I don't know if you recall, but a little over a year ago, I posted my .bi...