Search found 23 matches

by JKOBD
Mon Feb 20, 2006 9:54 pm
Forum: s100/s200
Topic: FJO injector driver / Romulator / Solid CEL
Replies: 8
Views: 5367

Try using the Romulator software from transtronics to upload the file to the romulator. If the problem persists, try removing the injector driver and see it the problem goes away, if it does not, contact Transtronics. www.transtronics.com It says that it has uploaded successfully everytime. Cycles ...
by JKOBD
Sun Feb 19, 2006 7:52 pm
Forum: s100/s200
Topic: FJO injector driver / Romulator / Solid CEL
Replies: 8
Views: 5367

FJO injector driver / Romulator / Solid CEL

Has anyone used the FJO injector driver box and tried to romulate? I am using the pocket romulator and am getting solid cel every time. I have tried two different ecus. Car runs great when I burn the bin to the chip. All my software works fine when I tune other cars. The only thing that was changed ...
by JKOBD
Sun Jan 09, 2005 11:05 pm
Forum: s100/s200
Topic: 1000cc
Replies: 2
Views: 1706

Also to add, you will probably want to try and get them to idle around 900rpms with roughly a 13.5:1 AF because of the larger dead time associated with those injectors. My street car idles 1600s around 1k rpms and 13:1 AF.
by JKOBD
Sun Sep 12, 2004 7:26 pm
Forum: s100/s200
Topic: anyone used the AEM 5 bar map sensor yet?
Replies: 1
Views: 1349

Re: anyone used the AEM 5 bar map sensor yet?

MikeD wrote:just wondering how it worked out. it's a 5 volt 3wire sensor so in theory it SHOULD work if calibrated correctly.
Anyone?
by JKOBD
Sun Sep 12, 2004 7:24 pm
Forum: s100/s200
Topic: RomEditor, PLX and Voltage...
Replies: 10
Views: 5302

Next you could try wiring the PLX directly to the ECU. I had a similar problem with my 95 Civic. I started to trace the voltage drop from the o2 sensor connector to the ECU, then found that half way through checking voltages the problem fixed itself. It turned out that I had a dirty connection in t...
by JKOBD
Wed Sep 08, 2004 12:14 pm
Forum: s100/s200
Topic: RomEditor, PLX and Voltage...
Replies: 10
Views: 5302

Disconnect the PLX from the ECU and measure the analog output to see if the ECU is pulling it down. The later PLXs should read 1V at 10:1, 2V at 20:1 With the PLX connected to the ECU measure the voltage on the ECU pins between D14 and D22, and check this is the same as the voltage as measured betw...
by JKOBD
Fri Sep 03, 2004 6:44 pm
Forum: s100/s200
Topic: RomEditor, PLX and Voltage...
Replies: 10
Views: 5302

RomEditor, PLX and Voltage...

Issues: At Idle: PLX reading: 13.5:1 RomEditor: 13.5:1 Voltage: 1.70 volts Accelerating: PLX reading: 13.6:1 RomEditor: 13.0:1 Voltage: 1.45 volts Cruising: PLX reading: 14.4:1 RomEditor: 13.4:1 Voltage: 1.65 volts It makes sense that the RomEditor matches the voltage as the Hondata gets its input f...
by JKOBD
Wed Aug 11, 2004 10:22 pm
Forum: s100/s200
Topic: Romulator problems
Replies: 8
Views: 4569

Mark,

When you go to settings, emulator, and confirm which COM port the romulator is in, do you get the following: Romulator 1.32 (Connected COMx)? Or do you get Romulator 00.00 (Connected COMx)?