Search found 44 matches
- Thu May 08, 2014 9:23 am
- Forum: s300 / SManager
- Topic: injector duty cycle & pulse width spike after gear shifting
- Replies: 6
- Views: 2880
Re: injector duty cycle & pulse width spike after gear shift
IAT temp too low.
- Sun Apr 27, 2014 4:38 am
- Forum: s300 / SManager
- Topic: Help ecu in limp mode? Can't get it out?
- Replies: 5
- Views: 2373
Re: Help ecu in limp mode? Can't get it out?
might be helpful if you can upload datalog here..
- Tue Apr 22, 2014 4:16 am
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
Re: distributor max to get 16 degree after change new coil
Im using fix timing light that cannot be adjust. Thanks.
- Mon Apr 21, 2014 12:00 pm
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
Re: distributor max to get 16 degree after change new coil
Sorry Spunkster. Typo error. It stamp with PR3-4. Thanks...
- Fri Apr 18, 2014 4:44 pm
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
Re: distributor max to get 16 degree after change new coil
The head not been milled. Im using standard B16a cam, cam pulley and engine block. The head stamp PR-4. Thanks for your help.
- Thu Apr 17, 2014 4:04 pm
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
Re: distributor max to get 16 degree after change new coil
red mark. the middle mark of three mark on crank pulley.
- Wed Apr 16, 2014 7:32 pm
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
Re: distributor max to get 16 degree after change new coil
using 2 fixed dial timing light. Thanks.
- Wed Apr 16, 2014 2:36 am
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
Re: distributor max to get 16 degree after change new coil
yes i try to set base timing using timing light. the single wire run to spark wire piston 1. Also using my friend timing light result still same. Thanks.
- Tue Apr 15, 2014 4:19 pm
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
Re: distributor max to get 16 degree after change new coil
the cam mark piston 1 at TDC. cam pulley UP arrow at the top.
- Mon Apr 14, 2014 4:41 pm
- Forum: s300 / SManager
- Topic: distributor max to get 16 degree after change new coil
- Replies: 15
- Views: 3453
distributor max to get 16 degree after change new coil
hello need some advice as my coil died so replace with new ign coil. After complete replace i want to set back base ignition to 16 degree using timing light.. The distributor go max to get 16 degree. My question is this coil causing the issue. Here the step 1.Replace bad coil 2. start up engine and ...
- Fri Apr 11, 2014 4:15 am
- Forum: s300 / SManager
- Topic: b16a hesitate part throttle.
- Replies: 4
- Views: 1719
Re: b16a hesitate part throttle.
i already found the problem. new o2 sensor having slow respond and make short term fuel trim cut max fuel. Swap with known good honda o2 sensor the hesitation/jerk go away. Thanks.
- Sun Apr 06, 2014 4:39 pm
- Forum: s300 / SManager
- Topic: Automatic ECU
- Replies: 4
- Views: 1828
Re: Automatic ECU
yes if that is OBD1 ECU...
- Wed Apr 02, 2014 8:26 pm
- Forum: s300 / SManager
- Topic: b16a hesitate part throttle.
- Replies: 4
- Views: 1719
Re: b16a hesitate part throttle.
i try swap fuel filter, spark plug, and last plug wire seem the hesitate became less...
- Wed Mar 26, 2014 9:37 am
- Forum: s300 / SManager
- Topic: b16a hesitate part throttle.
- Replies: 4
- Views: 1719
b16a hesitate part throttle.
- 2076 - the calibration (as an attachment) - a datalog of a problem (as an attachment) - ek4 b16a sir - p72 - intake whale penis, stock inj, stock cam, stock header right now mostly hesitate problem when in gear 4 or 5 while driving in other gear seem unable to duplicate hesitate problem. I'm using...