Search found 8607 matches

by Hondata
Sun Aug 04, 2019 8:31 am
Forum: s300 / SManager
Topic: RPMs & Duty Cycle Lines on Graph Wavy in VTEC
Replies: 4
Views: 199

Re: RPMs & Duty Cycle Lines on Graph Wavy in VTEC

The duty is wavy because it is calculated from the rpm so ignore the duty. The rpm signal has a lot of noise, and you can see it gets a lot worse at VTEC. So check the distributor wiring, the engine grounds and the ECU ground. Then look at the distributor.
by Hondata
Fri Aug 02, 2019 9:56 am
Forum: Civic Type R 2015+
Topic: Rev Match System Problem
Replies: 0
Views: 383

Rev Match System Problem

If you get a 'Rev Match System Problem' and an 'Emission System Problem' then don't tell us about it. Those errors mean that the rev match sub system has disabled itself because of some other error. They are symptoms of some other problem and don't tell us anything about what the problem might be. S...
by Hondata
Fri Aug 02, 2019 8:56 am
Forum: FlashPro Manager
Topic: Running very rich WOT
Replies: 13
Views: 851

Re: Running very rich WOT

Can you post the calibration too?
by Hondata
Thu Aug 01, 2019 3:47 pm
Forum: Civic Type R 2015+
Topic: CTR Losing boost at WOT after 4500rpm
Replies: 3
Views: 298

Re: CTR Losing boost at WOT after 4500rpm

Good. Thanks for the feedback.
by Hondata
Thu Aug 01, 2019 9:11 am
Forum: FlashPro Manager
Topic: Running very rich WOT
Replies: 13
Views: 851

Re: Running very rich WOT

Yes. Are you change all the values? I'd start by taking 5% off the whole table, another 5% below 2V, another 5% below 1.7 V and 5% below 1.2V (with a little blending in between).
by Hondata
Thu Aug 01, 2019 9:08 am
Forum: Traction Control with FlashPro
Topic: Traction Control + Knock Control Strategy
Replies: 9
Views: 528

Re: Traction Control + Knock Control Strategy

You can try changing the sensitivity but it usually does not work that well. It is worth looking at the engine / trans because sometimes it is something simple like the exhaust hitting the frame which gives the noise.
by Hondata
Thu Aug 01, 2019 8:16 am
Forum: S300 Calibrations
Topic: Need a Map B18C1 Bosch 2200 injectors
Replies: 1
Views: 185

Re: Need a Map B18C1 Bosch 2200 injectors

What are the dead times?
by Hondata
Wed Jul 31, 2019 12:57 pm
Forum: Traction Control with FlashPro
Topic: Traction Control + Knock Control Strategy
Replies: 9
Views: 528

Re: Traction Control + Knock Control Strategy

Last datalog at 19:15. Knock control goers up at 70kPa / 4000 rpm. It's not real knock so probably is from mechanical noise. You could zero the knock retard tables and that would at least give you consistent ignition timing, but be careful as it may result in more ignition than you planned. On one o...
by Hondata
Wed Jul 31, 2019 9:12 am
Forum: Traction Control with FlashPro
Topic: Traction Control + Knock Control Strategy
Replies: 9
Views: 528

Re: Traction Control + Knock Control Strategy

1. Nope, not normal. In the two datalogs I see the knock control is vastly different (55% vs 100%), and that will give different running and knock counts. 2. Disable the misfire detection. There is no downside. 3. The ECU will look at engine load and knock noise, and then adjust the knock control ac...
by Hondata
Wed Jul 31, 2019 8:29 am
Forum: Civic Type R 2015+
Topic: CTR Losing boost at WOT after 4500rpm
Replies: 3
Views: 298

Re: CTR Losing boost at WOT after 4500rpm

2:43 The wastegate is closed, the throttle is open but your boost drops and the engine goes lean. Seems to be related to VTEC too. I'd guess a massive boost leak like a split manifold, then I'd inspect the wastegate and turbo.
by Hondata
Tue Jul 30, 2019 8:23 pm
Forum: Applications
Topic: 2019 Honda hatchback CVT support
Replies: 20
Views: 1166

Re: 2019 Honda hatchback CVT support

You can change some limited parameters. Download the software and see.
by Hondata
Tue Jul 30, 2019 6:20 pm
Forum: K-Pro / KManager
Topic: Lambda Overlay issues after re-install
Replies: 8
Views: 473

Re: Lambda Overlay issues after re-install

Not something that's going to happen for the next release, but we will note it down.
by Hondata
Tue Jul 30, 2019 3:18 pm
Forum: K-Pro / KManager
Topic: Lambda Overlay issues after re-install
Replies: 8
Views: 473

Re: Lambda Overlay issues after re-install

Fixed for next release. Thank you.
by Hondata
Tue Jul 30, 2019 10:09 am
Forum: FlashPro Manager
Topic: FlashProManager 3.4.2
Replies: 10
Views: 662

Re: FlashProManager 3.4.2

Yes. Otherwise the cruise control has trouble.
by Hondata
Mon Jul 29, 2019 9:33 pm
Forum: Civic 2016+ 1.5 Turbo Americas/Asia
Topic: Question: Torque Table Targets
Replies: 2
Views: 241

Re: Question: Torque Table Targets

655Nm is the maximum for the table. The engine/turbo cannot make this much torque so there's no point raising it.