Search found 18641 matches

by Spunkster
Tue Jun 23, 2020 3:46 pm
Forum: K-Pro / KManager
Topic: RSX DTC P1166. Heater low voltage
Replies: 3
Views: 36

Re: RSX DTC P1166. Heater low voltage

This error has nothing to do with the secondary sensor. More than likely the primary sensor has been damaged and will need to be replaced.
by Spunkster
Tue Jun 23, 2020 9:03 am
Forum: CRV 2017+
Topic: 19 crv intake
Replies: 2
Views: 58

Re: 19 crv intake

If it is CARB approved then it should work, but any intake that is not CARB approved may cause issues.
by Spunkster
Tue Jun 23, 2020 9:02 am
Forum: Hondata Mobile
Topic: Hondata Mobile APK 1.5 (Android) for Dash
Replies: 50
Views: 13797

Re: Hondata Mobile APK 1.5 (Android) for Dash

I believe it will only work on the Civics.
by Spunkster
Mon Jun 22, 2020 2:38 pm
Forum: Traction Control with S300
Topic: D10 ELD 0.2v.
Replies: 7
Views: 167

Re: D10 ELD 0.2v.

You can try to use the offset to fix it, but that sometimes does not work as the voltage offset is not linear.
by Spunkster
Mon Jun 22, 2020 10:50 am
Forum: Civic Type R 2015+
Topic: 2020 FK8 jailbreak
Replies: 28
Views: 957

Re: 2020 FK8 jailbreak

You would have to check with the individual dealer to see if they are able to in fact properly jailbreak a 2020 Civic Type R.
by Spunkster
Mon Jun 22, 2020 10:44 am
Forum: K-Pro / KManager
Topic: VTEC engaging below set parameters
Replies: 9
Views: 81

Re: VTEC engaging below set parameters

Are you uploading to the ECU after making the changes in the calibration?
by Spunkster
Mon Jun 22, 2020 10:32 am
Forum: Accord 2008+ FlashPro
Topic: Lots of errors with flex fuel flash help 2019 2.0T Touring
Replies: 5
Views: 578

Re: Lots of errors with flex fuel flash help 2019 2.0T Touring

Hello, I have a 2019 Accord Sport 2.0T manual. I’ve been running the flex fuel tube on my car for about two months. I’ve just been able to figure out how to show psi Instead of mbar on the hondata I did a run yesterday to see my boost and it was only at 20 psi. If I’m not mistaken it should be arou...
by Spunkster
Mon Jun 22, 2020 10:18 am
Forum: K-Pro / KManager
Topic: Hondata K-Pro
Replies: 8
Views: 250

Re: Hondata K-Pro

I'm sorry, but since we are working from home, there is no way for me to check when it was received. If you want to send an email to accounts@hondata.com they can see if it has been processed.
by Spunkster
Mon Jun 22, 2020 10:17 am
Forum: s300 / SManager
Topic: s300 v3 not reading any sensors
Replies: 21
Views: 341

Re: s300 v3 not reading any sensors

I would recommend that you replace all the capacitors in the ECU.

https://www.hondata.com/products/access ... acitor-kit
by Spunkster
Fri Jun 19, 2020 1:43 pm
Forum: K-Pro / KManager
Topic: Cranking but not idling
Replies: 7
Views: 77

Re: Cranking but not idling

It could be any number of things at this point, since it has been completely disassembled since it was last running.
by Spunkster
Fri Jun 19, 2020 12:36 pm
Forum: K-Pro / KManager
Topic: Cranking but not idling
Replies: 7
Views: 77

Re: Cranking but not idling

Make sure the the rotary valve in the idle controller is not stuck. Have you entered the dead times for the injectors you are using?
by Spunkster
Fri Jun 19, 2020 11:14 am
Forum: K-Pro / KManager
Topic: Cranking but not idling
Replies: 7
Views: 77

Re: Cranking but not idling

Does this have an idle controller?
by Spunkster
Fri Jun 19, 2020 11:09 am
Forum: s300 / SManager
Topic: s300 v3 not reading any sensors
Replies: 21
Views: 341

Re: s300 v3 not reading any sensors

It looks like there may be a problem with the through hole and it may not be making contact with where it is supposed to go on the board.
by Spunkster
Fri Jun 19, 2020 11:07 am
Forum: s300 / SManager
Topic: Aim MXS 1.2 Strada Dash
Replies: 5
Views: 71

Re: Aim MXS 1.2 Strada Dash

Have you tried swapping RX and TX?

Are you sure the MXL and MXS use the same protocol?