Search found 40 matches
- Wed Mar 12, 2014 11:01 pm
- Forum: Traction Control with FlashPro
- Topic: ABS Module Wiring 2013 Si
- Replies: 27
- Views: 30489
Re: ABS Module Wiring 2013 Si
Thank you for the assistance, it is functioning correctly now.
- Wed Mar 12, 2014 10:17 am
- Forum: Traction Control with FlashPro
- Topic: ABS Module Wiring 2013 Si
- Replies: 27
- Views: 30489
Re: ABS Module Wiring 2013 Si
Can I do that, with the TC Input set to "None"? Otherwise car is next to impossible to drive?
- Wed Mar 12, 2014 9:50 am
- Forum: Traction Control with FlashPro
- Topic: ABS Module Wiring 2013 Si
- Replies: 27
- Views: 30489
Re: ABS Module Wiring 2013 Si
I'll try that soon here, thanks. IS the correct method to set the wheel speed set up to press "set" then "apply changes to TC" near the top of the window and that's it?
- Wed Mar 12, 2014 9:16 am
- Forum: Traction Control with FlashPro
- Topic: ABS Module Wiring 2013 Si
- Replies: 27
- Views: 30489
Re: ABS Module Wiring 2013 Si
I am using 1.7.2 Before my car went to the shop, its was connecting with FPM, I am not sure if this is what they used to setup the wheel speed setup.
So where do I go from here?
So where do I go from here?
- Wed Mar 12, 2014 3:20 am
- Forum: Traction Control with FlashPro
- Topic: ABS Module Wiring 2013 Si
- Replies: 27
- Views: 30489
Re: ABS Module Wiring 2013 Si
Had this installed today and I'm having some issues. With the TC dial off, it is engaging ignition cut. The only way I can drive without major issues is to turn the TC Input from ELD to None under Traction control in FPM Also, the TC window within FPM keeps saying Traction Control (disabled - softwa...
- Wed Mar 12, 2014 3:07 am
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
Re: AEM Wideband into FPM values
So I am having an issue with the displayed sensor data for the Wideband. It pretty much just stays at or within a couple tenths of 10.50..this is with the primary o2 all over the map. Any idea on what would cause this?
- Tue Mar 11, 2014 10:19 am
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
Re: AEM Wideband into FPM values
No worries, Ok, thanks for the clarification.
- Tue Mar 11, 2014 9:15 am
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
Re: AEM Wideband into FPM values
Thanks, is there a way I can still monitor what the primary o2 is doing for comparison?
- Mon Mar 10, 2014 3:38 pm
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
Re: AEM Wideband into FPM values
Thanks, so no need to use the AF corrected anymore right?
- Mon Mar 10, 2014 1:42 pm
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
Re: AEM Wideband into FPM values
Another question came to mind and I couldn't find an answer.
When reviewing a datalog with the WB hooked up to the ECU, which value or sensor will depict the data it has recorded in FPM? Will it replace the current AFR or AFR corrected values?
When reviewing a datalog with the WB hooked up to the ECU, which value or sensor will depict the data it has recorded in FPM? Will it replace the current AFR or AFR corrected values?
- Mon Mar 10, 2014 12:45 pm
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
Re: AEM Wideband into FPM values
Thank you for the quick response, you are always very helpful :)
- Mon Mar 10, 2014 11:35 am
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
Re: AEM Wideband into FPM values
Thanks!
So just so I am clear. Would I input the following?
0V / 4.99V
Lamda (:1)10 / 19.98
Wideband votlage input as ECT2? I intend to use ECT2/ pin A44
and disable ECT2 under MISC settings?
So just so I am clear. Would I input the following?
0V / 4.99V
Lamda (:1)10 / 19.98
Wideband votlage input as ECT2? I intend to use ECT2/ pin A44
and disable ECT2 under MISC settings?
- Sat Mar 08, 2014 7:46 pm
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: AEM Wideband into FPM values
- Replies: 13
- Views: 6078
AEM Wideband into FPM values
Hello, I am wanting to use my AEM Wideband (30-4100) for datalogging via FP. I will be using the A44 ECT2 Pin out as my ELD will be used for your TC system. Can you please confirm what if any values I would have to input into Voltage cells and Lambda (:1) cells? http://www.aemelectronics.com/Images/...
- Fri Feb 28, 2014 11:19 am
- Forum: Traction Control with FlashPro
- Topic: ABS Module Wiring 2013 Si
- Replies: 27
- Views: 30489
Re: ABS Module Wiring 2013 Si
Thanks!
- Fri Feb 28, 2014 9:38 am
- Forum: Traction Control with FlashPro
- Topic: ABS Module Wiring 2013 Si
- Replies: 27
- Views: 30489
Re: ABS Module Wiring 2013 Si
Hello, I wanted to check to ensure you did receive my S.A.S.E and hoping that it has been sent back. Could you please advise? Thanks.