Search found 40 matches

by dlc18
Fri Aug 10, 2018 4:48 pm
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

OK, I just emailed that info.
by dlc18
Fri Aug 10, 2018 12:56 pm
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

35764
by dlc18
Fri Aug 10, 2018 11:45 am
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

I am running CPR with this setup. Not sure if that makes a difference. I am also using Parallels that is partitioned on my Mac. It's running Windows XP, but this has never given me an issue in the past.
by dlc18
Fri Aug 10, 2018 11:44 am
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

Did the same thing.
by dlc18
Fri Aug 10, 2018 11:18 am
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

I turn the ignition on and press the throttle in which the vehicle bounces from 1500-2500 rpm. I then plug in my laptop with SManager already pulled up with the current calibration, while the vehicle is running. I will then press the arrow key "upload changes to the ECU". This usually does not work,...
by dlc18
Thu Aug 09, 2018 4:53 pm
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

I don't know what you mean by a test upload. I tried to upload the calibration I am currently running.
by dlc18
Thu Aug 09, 2018 10:11 am
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

I see. Try this one then.
by dlc18
Thu Aug 09, 2018 6:49 am
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

I thought that I did. There is an attachment of it. Is that not the correct way to upload it?
by dlc18
Wed Aug 08, 2018 11:17 pm
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

Also noticed in Sensors that "REVL" and "IGNC" switch from off to on while the revs are bouncing from 1500 to 2500 rpm. I disabled the full throttle shift and the burnout rev limit, with no resolution.
by dlc18
Wed Aug 08, 2018 9:57 pm
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

Re: S300v3 Will Not Rev past 2500 RPMs

Oh, and once I've plugged in SManager and got the revs working properlly, I can unplug my laptop with the car running and the revs continue to work until I turn off the ignition and turn it back on.
by dlc18
Wed Aug 08, 2018 6:11 pm
Forum: s300 / SManager
Topic: S300v3 Will Not Rev past 2500 RPMs
Replies: 17
Views: 1859

S300v3 Will Not Rev past 2500 RPMs

I am having an issue with S300 not allowing me to rev past 2500 rpms at times. This happens when I start the car without my laptop plugged in. It acts as if it is a rev limit activation bouncing from 1500-2500 RPMs. The lighter the throttle the faster it bounces, and the more throttle is given the s...
by dlc18
Sat Mar 31, 2012 12:15 pm
Forum: Coil Pack Retrofit
Topic: CPR wiring help!!!
Replies: 35
Views: 23968

Re: CPR wiring help!!!

Got down to Tim at Xact Dyno and he soldered in the transistor at Q37. Brought it home, plugged it in and it fired right up. SYNC light was flashing and everything was good. I want to thank you again for your time and patients with me and this situation. I know it is difficult to diagnose and explai...
by dlc18
Fri Mar 30, 2012 6:14 pm
Forum: Coil Pack Retrofit
Topic: CPR wiring help!!!
Replies: 35
Views: 23968

Re: CPR wiring help!!!

It tests good. I checked a16 on the board from the bottom of the board to the CPR connector with it plugged into the CPR box. Had 0.1 ohms. I did notice this; http://www.hondata.com/techvtecrelaydiagram.html does this mean that the PR4 does not have ALTC output? I traced pin A16 circuit on the board...
by dlc18
Fri Mar 30, 2012 1:57 pm
Forum: Coil Pack Retrofit
Topic: CPR wiring help!!!
Replies: 35
Views: 23968

Re: CPR wiring help!!!

O.K. did everything you told me to do. Distributor is completely stock except for spark plug wires and the power and TACH wires I took out. STILL no start and no SYNC light. ***Here is what is weird***Looking at my OBDII connector A, ALTC is the White/Green wire at pin A19. I follow that down throug...
by dlc18
Thu Mar 29, 2012 12:17 pm
Forum: Coil Pack Retrofit
Topic: CPR wiring help!!!
Replies: 35
Views: 23968

Re: CPR wiring help!!!

Ok, and I am still taking the "big" pins (blk/yel & blu wires) from the distributor completely out and replacing them with the blk/wht & purple wires from the CPR? I will not get to it until tonight, so if you have any other suggestions, please let me know.