Search found 12 matches

by Teamdiesel
Tue Dec 29, 2009 4:57 pm
Forum: S300 Calibrations
Topic: 1000cc map only 15psi 2.0L gsr
Replies: 7
Views: 7378

this map is not opening and would be perfect for my setup. Is there anyway you can repost this map?
by Teamdiesel
Mon Mar 30, 2009 12:10 pm
Forum: s300 / SManager
Topic: Car is knocking badddd!
Replies: 9
Views: 2670

how do i transfer/export a hondata s300 timing map to a program like snapfire?
by Teamdiesel
Mon Mar 30, 2009 11:22 am
Forum: s300 / SManager
Topic: Car is knocking badddd!
Replies: 9
Views: 2670

I have taken out up to 4 degrees and it still knocks slightly in 4th going up hill. Should I take out more or is there a downside to taking out too much timing in the lower regions?
by Teamdiesel
Fri Mar 27, 2009 11:40 am
Forum: s300 / SManager
Topic: Car is knocking badddd!
Replies: 9
Views: 2670

should I adjust fuel with these timing changes?
by Teamdiesel
Fri Mar 27, 2009 9:14 am
Forum: s300 / SManager
Topic: Car is knocking badddd!
Replies: 9
Views: 2670

remove how much at a time?
by Teamdiesel
Fri Mar 27, 2009 8:40 am
Forum: s300 / SManager
Topic: Car is knocking badddd!
Replies: 9
Views: 2670

Car is knocking badddd!

I have just finished my build and used a map from my last setup (which is similar to this one) to run the car until the tuner arrives next month. The setup is as follows: 85.5mmx92mm GSR block Fully race ported RLZ GSR head (chambers opened to 85mm) 12.5:1 cr Skunk2 stage2 cams (tuner series) Skunk2...
by Teamdiesel
Thu Mar 13, 2008 5:30 am
Forum: s300 / SManager
Topic: I need help with a situation
Replies: 1
Views: 1425

I need help with a situation

I would like to send you my maps to look at and see if you can give me any advice on improving them. Because the dyno here has closed its doors two weeks ago, I am forced now to tune my fuel settings alone with my wideband. I will include a datalog sheet of a third gear street pass that I tried to g...
by Teamdiesel
Fri Mar 07, 2008 8:14 pm
Forum: s300 / SManager
Topic: Aem wideband with hondata s300
Replies: 3
Views: 2671

Aem wideband with hondata s300

I have installed an AEM wideband but am having problems integrating it with the Hondata. The help files are of not much help so I need you help. I have hooked up the AEM wideband to the ELD D10 and clipped one end of the R136 & R138 resistors and cut the ELD wire and hooked the white 0-5v wire to it...
by Teamdiesel
Fri Mar 07, 2008 7:14 am
Forum: s300 / SManager
Topic: D10 ELD
Replies: 74
Views: 35613

me too, what happened?
by Teamdiesel
Sun Feb 24, 2008 2:27 pm
Forum: s300 / SManager
Topic: Cannot communicate with S300 after switching ECU's
Replies: 2
Views: 1623

Cannot communicate with S300 after switching ECU's

Hi, I was experirncing some major sputtering problems on my newly installed S300 and decided to switch back in my old Chrome chipped ecu to see if that is the problem. After switch ECU's it was dicovered that it was indeed something wrong on the s300 program. After switching back to the hondata s300...
by Teamdiesel
Sat Jan 12, 2008 4:09 am
Forum: s300 / SManager
Topic: D10 ELD
Replies: 74
Views: 35613

besides D10, what other methods can be used to connect the white wire of an AEM wideband to incoorporate it with the hondata s300?
by Teamdiesel
Fri Jan 11, 2008 7:17 pm
Forum: s300 / SManager
Topic: Where to connect the white wire on my AEM wideband guage?
Replies: 1
Views: 1224

Where to connect the white wire on my AEM wideband guage?

I just bought an AEM UEGO 6 in 1 wideband guage and sensor, along with a p28 equipped Hondata S300 unit. What I need to know is which wire/pin does the white 0-5v input wire tap into?