Search found 21 matches

by spoolind16
Thu Jun 02, 2011 10:18 am
Forum: s300 / SManager
Topic: Lean during wheelspin?
Replies: 3
Views: 1026

Re: Lean during wheelspin?

Thats what I was thinking but wanted to confirm. Thanks. Still curious though is it normal to see a little leaner A/F when wheel spinning. Its not going extremely lean; for example if the wheels aren't spinning and are under load 11.4 AFR when they start to spin 13.5 AFR.
by spoolind16
Thu Jun 02, 2011 8:11 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 106360

Re: SManager software requests

It would be nice to have the ablity to turn the fuel pump relay on and off with key-on engine-off. More than once I wanted to drain my fuel and had to rig a battery to the pumps.

Also the ablity to reivew if lean protection kicked in in the sensors window (similar to the way you have BstC displayed)
by spoolind16
Thu Jun 02, 2011 7:56 am
Forum: s300 / SManager
Topic: Lean during wheelspin?
Replies: 3
Views: 1026

Lean during wheelspin?

I noticed on my datalogs whenever I get a moderate amount of wheelspin my A/F goes leaner. This is causing me to hit lean cut which is annoying. I understand my lean cut is on the aggressive side. Lean 1 never triggers Lean 2 is the issue my Lean 2 settings are below: Max A/F: 11.8:1 Load: 14.1 psi ...
by spoolind16
Wed Jun 10, 2009 10:56 am
Forum: s300 / SManager
Topic: NO START AFTER WARM UP
Replies: 2
Views: 1154

Try replacing the ignitor. I had one go on me and everytime the car would cool down it would run for a short period of time.
by spoolind16
Wed Jun 10, 2009 10:22 am
Forum: s300 / SManager
Topic: Anti-Lag building very little boost
Replies: 9
Views: 3181

Martian wrote:60-1
Thats considerably smaller than my turbo. Hopefully 400 fuel value works. Anyone else have any suggestions? Whats a safe amount of timing to pull?
by spoolind16
Tue Jun 09, 2009 10:47 am
Forum: s300 / SManager
Topic: Anti-Lag building very little boost
Replies: 9
Views: 3181

Martian wrote:to be honest I'm not sure. But 400 seems to be the magic number for every car I've set up, and close to, if not exactlythe same on the cars my tuner friends have done.

Whats the largest turbo you used with this value? And how much boost did it build when als was active?
by spoolind16
Tue Jun 09, 2009 7:58 am
Forum: s300 / SManager
Topic: Anti-Lag building very little boost
Replies: 9
Views: 3181

post a datalog. raise your limiter to 6000, and change fuel to 400. Did you make sure to put a -40 and not 40 in the timing field? Yes I confirmed that I put -40 timing. I will try your suggestions today and hopefully post a log. Is the Fuel value an actual percentage of fuel enrichment or is it si...
by spoolind16
Mon Jun 08, 2009 3:51 pm
Forum: s300 / SManager
Topic: Anti-Lag building very little boost
Replies: 9
Views: 3181

Anti-Lag building very little boost

Frist off I'd like to say that I have searched this issue at length and have tried various fuel and timing retard combinations. For some reason I am only able to make 1.5psi with anti-lag I have tried settings up to: 350% fuel enrichment -40 deg of timing My launch rev limiter is 4000 rpm and fuel a...
by spoolind16
Wed Mar 18, 2009 2:05 pm
Forum: s300 / SManager
Topic: Set ignition timing option
Replies: 10
Views: 9466

Set ignition timing option

When using the set ignition timing option in SManager do you still have to jump the service connector like it shows in the service manual?
by spoolind16
Fri May 30, 2008 10:09 am
Forum: Romeditor 4 Software
Topic: Trouble With AEM UEGO
Replies: 2
Views: 11678

I seem to have gotten my AEM UEGO to work better now. FYI for those of you running one of these gauges. What I noticed is when I riched the car up to the gauge's max reading of 10.0:1 afr the output from the white wire (analog) read 1.54 volts instead of what the AEM manual said (0.00). Below are my...
by spoolind16
Thu May 29, 2008 11:23 am
Forum: Romeditor 4 Software
Topic: Trouble With AEM UEGO
Replies: 2
Views: 11678

Trouble With AEM UEGO

I've been searching around this forum and found that the best place to take the power for a wideband is from the fuse panel. My question is: Why not take it off the ECU power and ground from the 'A' connector. This is what I did but I fear that its messing with my wideband readings. It seems the ric...
by spoolind16
Sun May 25, 2008 2:12 pm
Forum: Romeditor 4 Software
Topic: Hondata Romulator with RomEditor Cable
Replies: 1
Views: 7352

Hondata Romulator with RomEditor Cable

Just wondering if and how I can use my RomEditor 4 usb-serial cable with the transonics rom emulator. Is it possible?
by spoolind16
Thu Nov 29, 2007 5:52 pm
Forum: Romeditor 4 Software
Topic: 64 bit support
Replies: 7
Views: 7734

thats a decent idea but I dont feel like taking my brand new laptop apart.
by spoolind16
Sun Nov 25, 2007 10:40 am
Forum: Romeditor 4 Software
Topic: 64 bit support
Replies: 7
Views: 7734

Well XP is being phased out. And eventually 64 bit will be the only option. Granted this won't be for awhile. But still is there no option? Perhaps for those of us who want a 64 bit driver can we pay an extra fee (assuming theres enough of us)?
by spoolind16
Wed Nov 21, 2007 12:53 am
Forum: Romeditor 4 Software
Topic: 64 bit support
Replies: 7
Views: 7734

Ok so then what do I do? I paid all this money for my Hondata and I'm unable to use it? Thats not very good.

And before you tell me its my fault for buying a Vista computer, well I had no choice as thats what the computer came with. Like all new computers now Vista is going to be standard.