Search found 43 matches

by flip1199
Tue Jun 20, 2006 11:13 am
Forum: s300 / SManager
Topic: s300 tuning woes...
Replies: 7
Views: 4242

excuse my ignorance but what is eld?
by flip1199
Mon Jun 19, 2006 4:51 pm
Forum: s300 / SManager
Topic: s300 tuning woes...
Replies: 7
Views: 4242

so in parameter, just unclick closed loop operation and i should be fine?

and btw, i was actually going off the plx instructions that came with the device not yours, as i installed this prior to running hondata
by flip1199
Mon Jun 19, 2006 4:25 pm
Forum: s300 / SManager
Topic: s300 tuning woes...
Replies: 7
Views: 4242

its a plx m300. i wired it like the instructions said....

white signal output wire of the plx to o2 signal input.
and a 1k ohm resistor between 12v heater and heater ground.
by flip1199
Sun Jun 18, 2006 9:28 pm
Forum: s300 / SManager
Topic: s300 tuning woes...
Replies: 7
Views: 4242

s300 tuning woes...

Well i setup my base map for my car and got it to idle around 1500rpm at around 14-15 a/f. here's the problem i ran into. with the car fully warmed up and idleing the a/f ratio would jump to 17-19 i blip the throttle and it goes back down to 14-15. any ideas on why this would happen. also it appears...
by flip1199
Wed Apr 12, 2006 4:56 pm
Forum: s300 / SManager
Topic: Auto Tune?
Replies: 15
Views: 17057

how do u use the autotune feature on the s300? i don't see a auto tune button. or am i supposed to click and hold down the "base autotune" button?
by flip1199
Tue Apr 11, 2006 5:41 pm
Forum: s300 / SManager
Topic: gm 3barmapsenser
Replies: 20
Views: 13304

any update on this? i know there has to be atleast a couple hundred guys running the gm 3 bar...
by flip1199
Thu Apr 06, 2006 12:39 pm
Forum: s300 / SManager
Topic: h23 code 21???
Replies: 12
Views: 6817

oh ok, i socketed the ecu. but i'm just bit the bullet and sent you another known good ecu. you should have gotten it this morning. it was a pr4 that was pre-chipped.
by flip1199
Wed Apr 05, 2006 5:01 pm
Forum: s300 / SManager
Topic: h23 code 21???
Replies: 12
Views: 6817

yup j12 is cut.
by flip1199
Wed Apr 05, 2006 1:03 pm
Forum: s300 / SManager
Topic: h23 code 21???
Replies: 12
Views: 6817

i would but nothing shows up when i datalog or even when i had the car running and i had the sensors and diplays screen up. i cut the j1 jumper and the code is still there so i'm guessing it's a bad ecu? :?: on a side note, once u guys recieve a ecu how long does it take u to socket it and get it re...
by flip1199
Tue Apr 04, 2006 6:01 pm
Forum: s300 / SManager
Topic: h23 code 21???
Replies: 12
Views: 6817

here my basemap
by flip1199
Sun Apr 02, 2006 8:01 pm
Forum: s300 / SManager
Topic: which calibrations to use NEED HELP
Replies: 1
Views: 1712

the h22 one
by flip1199
Fri Mar 31, 2006 1:07 pm
Forum: s300 / SManager
Topic: h23 code 21???
Replies: 12
Views: 6817

i did that but the cell still remains. also what do i do about not being able to see the sensors or display?
by flip1199
Fri Mar 31, 2006 12:30 pm
Forum: s300 / SManager
Topic: h23 code 21???
Replies: 12
Views: 6817

i'm using a p28 ecu on a non-vtec h23.
by flip1199
Fri Mar 31, 2006 10:11 am
Forum: Applications
Topic: which p30 do i have?
Replies: 2
Views: 2466

which p30 do i have?

ok on your application chart it list 3 different p30's. one of which can't be used with hondata s300. how would i be able to tell which one i have. here are the numbers on it "37820-p30-020"
by flip1199
Thu Mar 30, 2006 9:44 pm
Forum: s300 / SManager
Topic: h23 code 21???
Replies: 12
Views: 6817

h23 code 21???

ok i went to start up my car today on a h22 turbo basemap. i have the basemap setup for 1000cc injectors. i start the car and it idles and the smanager says it's online but there is a solid cel and it wont display any of the sensor?? also i clicked on error codes and it showed nothing, but i jumped ...