Search found 144 matches

by ITR 1102
Wed Oct 12, 2016 7:24 am
Forum: K-Pro / KManager
Topic: Live tuning help
Replies: 6
Views: 1857

Re: Live tuning help

I'll do some more testing over the weekend and report back with the requested information. When testing it last night to obtain a datalog for you, it operated correctly. The only change I made was to the selection of the live tuning tables. For my test last night, I selected only the 0 and 10 degree...
by ITR 1102
Mon Oct 10, 2016 8:13 am
Forum: K-Pro / KManager
Topic: Live tuning help
Replies: 6
Views: 1857

Re: Live tuning help

I tried making changes to the 0 and 10 degree low cam fuel tables and the low cam angle table. I tried doing them individually so that Live Tuning memory wasn't maxed out but it didn't seem to make a difference.
by ITR 1102
Mon Aug 04, 2014 6:19 pm
Forum: K-Pro / KManager
Topic: KPro / KManager requests
Replies: 121
Views: 48648

Re: KPro / KManager requests

I'd like to inquire about the possibilities of real-time programming on the K-Pro system (specifically on RSX and K swapped platforms). Tuning the K series engine takes longer than the typical D,B,H. Adding the requirement to power off, upload and restart adds even more time to the tuning session. ...
by ITR 1102
Thu Jul 31, 2014 11:10 am
Forum: K-Pro / KManager
Topic: KPro / KManager requests
Replies: 121
Views: 48648

Re: KPro / KManager requests

I'd like to inquire about the possibilities of real-time programming on the K-Pro system (specifically on RSX and K swapped platforms). Tuning the K series engine takes longer than the typical D,B,H. Adding the requirement to power off, upload and restart adds even more time to the tuning session. W...
by ITR 1102
Fri Aug 31, 2012 12:30 pm
Forum: s300 / SManager
Topic: ECU Socket Tester
Replies: 2
Views: 1492

ECU Socket Tester

I am having a P28 ECU problem and am using the Hondata S300 socket tester to help, but I am unable to resolve the issue. There are 2 LED's that are either not lit or are very weak. I have resoldered the board and retested, but the problem persists on the same 2 pins. I tested for continuity and resi...
by ITR 1102
Thu Aug 23, 2012 2:57 pm
Forum: s300 / SManager
Topic: NEW HOndata TRaction COntol $$$795 $$$$4
Replies: 5
Views: 2821

Re: NEW HOndata TRaction COntol $$$795 $$$$4

I was happy to see it being tested out at the ITR Expo earlier this week at Mid Ohio. I didn't get a chance to watch or hear how things were going, but judging by the fact that it is for sale, I am going to say that testing went quite well. I'm adding this to my wish list now.
by ITR 1102
Sun Feb 12, 2012 9:50 am
Forum: s300 / SManager
Topic: SManager V2.0.0 (beta)
Replies: 23
Views: 7384

Re: SManager V2.0.0 (beta)

I didn't see any mention of an upgrade for V1 users to the V2. Are you guys offering a trade up program for this? Having the additional inputs would be nice.
by ITR 1102
Mon Oct 31, 2011 7:06 pm
Forum: s300 / SManager
Topic: Hondata Map Sensor Question
Replies: 1
Views: 1126

Hondata Map Sensor Question

For lower boost setups such as mine, which Hondata map sensor is the best to use? I like the idea of the presets in the software for the 4 bar sensor, but there are not presets for the 3 bar sensor. I have read about a loss of resolution with the higher the sensor's bar rating, but don't know if tha...
by ITR 1102
Mon Jun 21, 2010 10:30 am
Forum: Non-Hondata
Topic: 204 F cruising on highway. Too hot?
Replies: 5
Views: 2730

Update: I put a 170 * F thermostat in, drained entire system and filled with 75% water, 25% Honda Blue coolant, and added a bottle of water wetter to the mixture. I removed the fan shroud and installed both 12" Mishimoto dual slim fans. I set the fan control override to 178 * F, with a maximum MPH a...
by ITR 1102
Wed Jun 16, 2010 5:28 pm
Forum: Non-Hondata
Topic: 440cc ok with this LHT JRSC setup on 98' ITR?
Replies: 2
Views: 2290

I upgraded to the 550's.
Walbro pump and I keep stock FP, I wasn't about to go down that road.

So far so good; with a little bit of room to grow.
by ITR 1102
Tue Jun 15, 2010 3:36 pm
Forum: Non-Hondata
Topic: 204 F cruising on highway. Too hot?
Replies: 5
Views: 2730

Well, I don't have any leaks. The fluid is full and stays full. I bled the system when I filled it after swapping radiators. LHT advised that I upgrade my radiator, assuming that my stock one was old and no longer efficient. I wish I knew the MPH that my Mishimoto 12" slim fans stalled at. If it is ...
by ITR 1102
Tue Jun 15, 2010 11:00 am
Forum: Non-Hondata
Topic: 204 F cruising on highway. Too hot?
Replies: 5
Views: 2730

204 F cruising on highway. Too hot?

Is this overly hot? It is only 80 degrees outside, so I feel that it is. The car is supercharged, but still... I have a Mishimoto performance radiator. When I slow down, the temps drop down to about 197 (according to Hondata S300 datalog). The motor is only 2 years old, as is water pump, etc. I can'...
by ITR 1102
Tue Jun 01, 2010 4:27 pm
Forum: s300 / SManager
Topic: SManager V1.4.7 (beta)
Replies: 19
Views: 7898

mine works fine. datalogged for an hour and 15 minutes straight yesterday. ECU does not reset by itself (randomly while driving) anymore! yay! I don't use PWM boost control, so I can't test that out for you. The ECU used to reboot at least once every drive if I was on the highway. No issues since up...
by ITR 1102
Tue Jun 01, 2010 4:20 pm
Forum: s300 / SManager
Topic: Thinking of switching from boosted s200 to s300
Replies: 9
Views: 2808

launch control and anti-lag have nothing to do with boost control. Cool! Next question: I have the version4 s200, can I transfer over my calibrations to the s300? If yes, how? SManager allows you to open the .bin or .re4 calibration. It will be more than a good starting point, but I think you will ...
by ITR 1102
Sun May 09, 2010 6:58 am
Forum: s300 / SManager
Topic: SManager: 2D Graph is maximized; can't view tables
Replies: 2
Views: 1641

SManager: 2D Graph is maximized; can't view tables

Using Previous release as well as Beta version: When comparing some fuel curves from different calibrations, I maximized the graph's view by sliding the vertical bar all the way to the left, covering up the tables. The handle still shows up, but it will not drag back to the right... Tables are now p...