Search found 18 matches

by onespeed
Tue Jun 03, 2008 1:52 am
Forum: Non-Hondata
Topic: auto ecu
Replies: 2
Views: 5194

auto ecu

Is there a way to determine if an ecu is for an automatic by looking at the part number? What about an automatic with vtec? Thanks
by onespeed
Sat Nov 10, 2007 12:04 pm
Forum: s300 / SManager
Topic: s300 not communicating
Replies: 12
Views: 4996

can I load a calibration without affecting the tuning set up that my car is running on right now?
by onespeed
Fri Nov 09, 2007 8:52 pm
Forum: s300 / SManager
Topic: s300 not communicating
Replies: 12
Views: 4996

tried to make the changes, but when i pull up the parameters window, everything was gray. so now i have no clue.
by onespeed
Thu Nov 08, 2007 10:47 pm
Forum: s300 / SManager
Topic: s300 not communicating
Replies: 12
Views: 4996

Thanks for your post. Sorry about being so vague in my last post. This is the first time I'm using my laptop to communicate with my ecu.

I got it to work, when I change the launch rpm in the parameters window, do I just upload it to the ecu? Thanks again.
by onespeed
Wed Nov 07, 2007 10:15 pm
Forum: s300 / SManager
Topic: s300 not communicating
Replies: 12
Views: 4996

I don't have any error codes, the screen doesn't do anything with the engine running or not. All I want to do is set the launch control. thanks
by onespeed
Wed Nov 07, 2007 12:50 am
Forum: s300 / SManager
Topic: s300 not communicating
Replies: 12
Views: 4996

s300 not communicating

my car was dyno'd and raced, i never set the launch control due to vss not working. i fixed vss and want to set the launch rpm, but i can't get the ecu to communicate with my laptop. this is the first time i am trying to use my ibm notebook to set anything. i went through the driver install and the ...
by onespeed
Sun Jul 29, 2007 1:02 am
Forum: s300 / SManager
Topic: two step
Replies: 1
Views: 1458

two step

how does the two step feature in the s300 control the rpm? does it cut out the ignition like an msd?
by onespeed
Sat Apr 14, 2007 12:07 am
Forum: s300 / SManager
Topic: gm map
Replies: 2
Views: 1725

thanks for the help, i really appreciate it.
by onespeed
Fri Apr 13, 2007 1:10 am
Forum: s300 / SManager
Topic: gm map
Replies: 2
Views: 1725

gm map

How do you splice in a gm map sensor to a honda wiring harness. obd1? I need to know what pin D17 (map sb), D19 (vcc1), and D21 (sg1) are so i can splice in my gm map.
by onespeed
Tue Mar 20, 2007 12:41 am
Forum: s300 / SManager
Topic: ecu chipping
Replies: 1
Views: 1365

ecu chipping

What does it cost to have the ecu chipped if the s300 is'nt bought directly from hondata?
by onespeed
Sun Jul 16, 2006 12:21 am
Forum: s300 / SManager
Topic: wiring harness
Replies: 7
Views: 3604

[quote="Djbower1"]wires you need are vss, iat, ect, map, iacv, vtech sol, dissy & Coil, injectors and that's it. I made a harness to run off two wires (power & earth) Follow the hondata wiring diagram and you cant go wrong. you just need to adapt it abit. Hope this help http://www....
by onespeed
Fri Jul 14, 2006 11:04 pm
Forum: s300 / SManager
Topic: wiring harness
Replies: 7
Views: 3604

I downloaded it but couldnt find what errors could be disabled. Is it even viable to modify a wiring harness to be used on a race only car? I dont want all the mess under my dash.
by onespeed
Tue Jul 11, 2006 10:41 pm
Forum: s300 / SManager
Topic: wiring harness
Replies: 7
Views: 3604

what about the vss, a/c,etc. And if I keep only the pins that are needed, supply power and grounds, will I be able to use the hondata on my race car? Would you be able to advise me as i make my harness?
by onespeed
Tue Jul 11, 2006 8:52 am
Forum: s300 / SManager
Topic: wiring harness
Replies: 7
Views: 3604

wiring harness

Im trying to modify a wiring harness so i can use hondata on my race car. Can the electric load detector be ignored by the s300 system?
by onespeed
Thu Jun 15, 2006 11:44 pm
Forum: s300 / SManager
Topic: hondata
Replies: 4
Views: 2310

Thanks for the replies. What would it cost to have hondata socket an ecu?