Search found 33 matches
- Thu May 25, 2023 6:07 pm
- Forum: K-Pro / KManager
- Topic: KManager issues between laptops
- Replies: 6
- Views: 286
Re: KManager issues between laptops
I updated to the new Beta version and it's now working.
- Thu May 25, 2023 5:56 pm
- Forum: K-Pro / KManager
- Topic: KManager issues between laptops
- Replies: 6
- Views: 286
Re: KManager issues between laptops
I forgot to mention that I also have the "Wideband Input" under settings to use "Analog Input 0"
Everything seems to be configured the same as my old laptop.
Everything seems to be configured the same as my old laptop.
- Thu May 25, 2023 5:52 pm
- Forum: K-Pro / KManager
- Topic: KManager issues between laptops
- Replies: 6
- Views: 286
Re: KManager issues between laptops
I believe it is a Bosch... it's been a few years. I have it setup under "Parameters" > "Analog inputs" > "Analog 0" of my calibration. It's working fine on my old laptop and I can view the A/F in real time. When viewing the A/F in "Display" on the new laptop i...
- Thu May 25, 2023 11:52 am
- Forum: K-Pro / KManager
- Topic: KManager issues between laptops
- Replies: 6
- Views: 286
Re: KManager issues between laptops
Changing it in the sensor list is exactly what I was missing. Thank you for the help.
Any ideas of why I'm not getting readings from my wideband?
"Display" tab > A/F:1
Any ideas of why I'm not getting readings from my wideband?
"Display" tab > A/F:1
- Thu May 25, 2023 7:55 am
- Forum: K-Pro / KManager
- Topic: KManager issues between laptops
- Replies: 6
- Views: 286
KManager issues between laptops
Hello, I have switched to a new tuning laptop and when using KManager for my AP1 I noticed that the Map display is using ("/psi) no matter what I change the pressure units to in "Settings" and the AF display is also not reading from my wideband which I have setup in Parameters>Analog ...
- Mon Mar 06, 2023 8:57 pm
- Forum: Civic Type R 2015+
- Topic: FK8 Factory Calibrations
- Replies: 3
- Views: 1932
FK8 Factory Calibrations
Quick question... are the FK8 factory calibrations taken from the factory ecu? I'm asking because the air charge limit cells are all at 1536. Just curious.
- Tue Jan 19, 2021 2:26 pm
- Forum: FlashPro Manager
- Topic: 2019 CTR - Descending knock steps
- Replies: 2
- Views: 904
Re: 2019 CTR - Descending knock steps
I got it figured out. My apologies for not updating the thread.
Thanks again!
Thanks again!
- Thu Jan 14, 2021 3:10 pm
- Forum: FlashPro Manager
- Topic: 2019 CTR - Descending knock steps
- Replies: 2
- Views: 904
2019 CTR - Descending knock steps
Hello, I'm seeing descending knock steps in cylinders 2/4 at WOT beginning at 2600rpm and stepping down until 6k rpm. I'm assuming that this is noise as it is decreasing and not increasing. However, I am hesitant to lower the knock sensitivity in these 2 cylinders. Thoughts? - I've tried to upload t...
- Tue Jan 05, 2021 2:45 pm
- Forum: Civic Type R 2015+
- Topic: Disable EGT Air Charge question
- Replies: 3
- Views: 1595
Re: Disable EGT Air Charge question
That makes sense. I was reading the tuning guide and saw the note about not wanting to see 0mm and it through me off.
Thank you and congrats on the team up with Spoon. I've been following then since the early 90's.
Thank you and congrats on the team up with Spoon. I've been following then since the early 90's.
- Mon Jan 04, 2021 4:43 pm
- Forum: Civic Type R 2015+
- Topic: Disable EGT Air Charge question
- Replies: 3
- Views: 1595
Disable EGT Air Charge question
Hello and Happy New Year! I've been using KPro and Flashpro for the past few years to help with mostly N/A tuning, but I've just purchased a CTR and want to learn as much as I can with my personal vehicle. I recently setup a base calibration, did a few datalogs with the Disable EGT checked, and noti...
- Wed Jun 24, 2020 12:26 pm
- Forum: K-Pro / KManager
- Topic: VTEC engaging below set parameters
- Replies: 9
- Views: 2659
- Wed Jun 24, 2020 12:06 pm
- Forum: K-Pro / KManager
- Topic: VTEC engaging below set parameters
- Replies: 9
- Views: 2659
Re: VTEC engaging below set parameters
Any ideas?
- Mon Jun 22, 2020 11:00 am
- Forum: K-Pro / KManager
- Topic: VTEC engaging below set parameters
- Replies: 9
- Views: 2659
- Sun Jun 21, 2020 3:04 pm
- Forum: K-Pro / KManager
- Topic: VTEC engaging below set parameters
- Replies: 9
- Views: 2659
Re: VTEC engaging below set parameters
Update:
VTEC seems to be engaging at 4600rpm no matter what kPa I have it set to. I've set it at 78, 88, 98 and 102 all with the same result.
VTEC seems to be engaging at 4600rpm no matter what kPa I have it set to. I've set it at 78, 88, 98 and 102 all with the same result.
- Sun Jun 21, 2020 7:02 am
- Forum: K-Pro / KManager
- Topic: VTEC engaging below set parameters
- Replies: 9
- Views: 2659
Re: VTEC engaging below set parameters
Yes. I'm in Denver. The max I see here is 84 kpa. I've setup my tables accordingly and the ecu reads the correct cells (kpa/rpm) so I don't see why it would be engaging VTEC earlier. Hopefully I'll here back.