Search found 18 matches

by WillP
Tue Jul 16, 2019 8:37 am
Forum: K-Pro Calibrations
Topic: K20A2 EP3 European ITB base calibration question
Replies: 4
Views: 988

Re: K20A2 EP3 European ITB base calibration question

Hi,

Just to follow this up, the ITB's fell through so this one can be closed.

Thanks!
by WillP
Tue Mar 26, 2019 1:33 am
Forum: K-Pro / KManager
Topic: PRA Kpro V4 AEM wideband install
Replies: 1
Views: 802

PRA Kpro V4 AEM wideband install

Hi,


How is an AEM wideband sensor applied and setup as an AFR input on Kpro V4 PRA?


Thanks
by WillP
Fri Mar 22, 2019 2:12 pm
Forum: K-Pro Calibrations
Topic: Kpro V2 fuel percentage adjustment
Replies: 11
Views: 1278

Re: Kpro V2 fuel percentage adjustment

I have 2 running on Kpro V4 that need wideband setup
by WillP
Fri Mar 22, 2019 10:04 am
Forum: K-Pro Calibrations
Topic: Kpro V2 fuel percentage adjustment
Replies: 11
Views: 1278

Re: Kpro V2 fuel percentage adjustment

Ok thank you that explains it. Are there any recommendations for these on this particular setup? Is there anything plug and play to swap the current sensor out? If not then I am correct to assume that I can fit a wideband sensor in the secondary lambda hole? If I am correct then how is the wideband ...
by WillP
Fri Mar 22, 2019 12:58 am
Forum: K-Pro Calibrations
Topic: Kpro V2 fuel percentage adjustment
Replies: 11
Views: 1278

Re: Kpro V2 fuel percentage adjustment

37820-PRA-E12
by WillP
Thu Mar 21, 2019 2:47 pm
Forum: K-Pro Calibrations
Topic: Kpro V2 fuel percentage adjustment
Replies: 11
Views: 1278

Re: Kpro V2 fuel percentage adjustment

Hey, Just to follow up on this, I have been working on the Dyno again today. I tested the software so loaded the 'dyno tuned' base map, did a run and logged it. Then proceeded to work on the fuel tables based on the percentage guide. I applied the percentage as advised, uploaded and repeated the seq...
by WillP
Wed Mar 13, 2019 4:25 am
Forum: K-Pro Calibrations
Topic: K20A2 EP3 European ITB base calibration question
Replies: 4
Views: 988

K20A2 EP3 European ITB base calibration question

Hi,

I will be working on a EP3 K20A2 I am fitting ITB's.


Hardware

ITB's
310 cc injectors
Full manifold back exhaust system with decat
Stock cams

Are the base calibrations with KManager ok to work from with ITB or can a ITB base calibration be supplied to me at all?


Kind regards
by WillP
Tue Mar 12, 2019 9:56 am
Forum: K-Pro Calibrations
Topic: Kpro settings for LC and Overrun
Replies: 5
Views: 934

Re: Kpro settings for LC and Overrun

Images are attached
by WillP
Tue Mar 12, 2019 6:45 am
Forum: K-Pro Calibrations
Topic: Kpro settings for LC and Overrun
Replies: 5
Views: 934

Re: Kpro settings for LC and Overrun

Is this on a turbo vehicle? Retarding the ignition means that you are reducing the timing. a negative value will cause it to add timing as you will be using double negatives. I do not understand your other questions. This is what I am talking about, the RPM data it open to change on SManager. https...
by WillP
Tue Mar 12, 2019 6:22 am
Forum: K-Pro Calibrations
Topic: EP3 K20A2 fuel pressure
Replies: 1
Views: 756

EP3 K20A2 fuel pressure

Hi,

Can KManager show fuel pressure data at all? I cannot see it if it does.

Also how is the stock fuel pressure regulated? Is it worth setting up a fuel pressure regulator just before the rail feed with or without a return line?

I am looking into this for an ITB conversion.

Thanks :)
by WillP
Tue Mar 12, 2019 1:33 am
Forum: K-Pro Calibrations
Topic: Kpro settings for LC and Overrun
Replies: 5
Views: 934

Re: Kpro settings for LC and Overrun

OK that's fine but either way, the entered amount of ignition angle is never met on the live data?

The second question, overrun top cam and low ca, RPM data is locked to 3000 max and not changeable when I am sure it was changeable before?
by WillP
Mon Mar 11, 2019 9:51 am
Forum: K-Pro Calibrations
Topic: Kpro settings for LC and Overrun
Replies: 5
Views: 934

Kpro settings for LC and Overrun

Hey, I have a couple of questions. I have been working with the launch control settings for a customer with the anti lag settings https://cdn1.imggmi.com/uploads/2019/3/11/9bc18e5814408a3a62622202f2ffcb1f-full.jpg Fuel enrichment, no matter how much i put in, nothing changes. Is this conflicted by o...
by WillP
Mon Mar 11, 2019 8:36 am
Forum: K-Pro Calibrations
Topic: Kpro V2 fuel percentage adjustment
Replies: 11
Views: 1278

Re: Kpro V2 fuel percentage adjustment

Yes I made changes throughout all tables.

I've got another one to work on this week so I will see how that one goes :)
by WillP
Thu Mar 07, 2019 4:16 pm
Forum: K-Pro Calibrations
Topic: Kpro V2 fuel percentage adjustment
Replies: 11
Views: 1278

Re: Kpro V2 fuel percentage adjustment

Yes of course.