Search found 24 matches
- Mon Mar 12, 2007 5:37 pm
- Forum: Applications
- Topic: S300 into CRX ED9 with B16A1?
- Replies: 2
- Views: 2913
- Sat Mar 10, 2007 3:23 pm
- Forum: Applications
- Topic: S300 into CRX ED9 with B16A1?
- Replies: 2
- Views: 2913
S300 into CRX ED9 with B16A1?
I want to put my S300 into my upcoming project, a CRX ED9 with a B16A1 swap(originally D16). Now this car is OBD0 I guess - what is needed to make S300 function properly?
- OBD1 ECU like P28/P30
- Distributor from OBD1 B16A (or any other similar)
- WHAT ELSE? Harnesses?
- OBD1 ECU like P28/P30
- Distributor from OBD1 B16A (or any other similar)
- WHAT ELSE? Harnesses?
- Tue Jan 23, 2007 8:48 pm
- Forum: s300 / SManager
- Topic: Possible? ECU killing o2-sensors?
- Replies: 6
- Views: 2928
- Mon Jan 22, 2007 1:16 pm
- Forum: s300 / SManager
- Topic: Possible? ECU killing o2-sensors?
- Replies: 6
- Views: 2928
- Sat Jan 20, 2007 10:15 am
- Forum: s300 / SManager
- Topic: Possible? ECU killing o2-sensors?
- Replies: 6
- Views: 2928
Possible? ECU killing o2-sensors?
Setup is P28 with S300 and a B16A2 with I/H/E. Works fine but from time to time my o2-sensor dies (4-wire). Replacing the o2-sensor will make the car normal again.
Is there a possibility that a bad socket job or anything else is killing my o2-sensor? Anything else?
Is there a possibility that a bad socket job or anything else is killing my o2-sensor? Anything else?
- Sat Nov 11, 2006 2:07 pm
- Forum: s300 / SManager
- Topic: Strange behavior with AFR - richens at zero throttle
- Replies: 1
- Views: 1636
Strange behavior with AFR - richens at zero throttle
I went out driving today and after half an hour or so I noticed that my AF gauge read below 10:1 (off the scale). The thing is that this only happens when I have no acceleration or deceleration, as soon as I just barely touch the gas pedal the AFR goes to around 14.7:1 where it should be. Else I nee...
- Thu Jul 20, 2006 1:26 am
- Forum: s300 / SManager
- Topic: How do I wire in my Wideband?
- Replies: 25
- Views: 12267
- Wed Jul 19, 2006 1:17 pm
- Forum: s300 / SManager
- Topic: How do I wire in my Wideband?
- Replies: 25
- Views: 12267
- Wed Jul 19, 2006 1:08 pm
- Forum: s300 / SManager
- Topic: Minor hicups after S300 install - hints?
- Replies: 8
- Views: 4129
- Wed Jul 12, 2006 1:06 pm
- Forum: s300 / SManager
- Topic: Minor hicups after S300 install - hints?
- Replies: 8
- Views: 4129
We did not post that calibration on the forum. That was posted by some other user. I know, just wanted to know someones opinion on the matter :) As for Full Throttle Shift, do you have the wire connected to the clutch switch so that it can actually tell when you are shifting? Sorry for not searchin...
- Wed Jul 12, 2006 10:53 am
- Forum: s300 / SManager
- Topic: Minor hicups after S300 install - hints?
- Replies: 8
- Views: 4129
- Wed Jul 12, 2006 10:34 am
- Forum: Non-Hondata
- Topic: A Mystery Problem... Stalling when stopping or accelerating.
- Replies: 2
- Views: 2395
- Wed Jul 12, 2006 10:27 am
- Forum: s300 / SManager
- Topic: Minor hicups after S300 install - hints?
- Replies: 8
- Views: 4129
Ok I see - no the car has not been on a dyno yet. I have to drive like 900km to get there(I live in Norway) and have not had the time yet. Thanks Spunkster :) About the stock EUDM P30 map - may it be so that this is NOT an actual copy of the original map since it leans out so much? It is supposed to...
- Wed Jul 12, 2006 10:04 am
- Forum: s300 / SManager
- Topic: How do I wire in my Wideband?
- Replies: 25
- Views: 12267
- Wed Jul 12, 2006 4:12 am
- Forum: s300 / SManager
- Topic: Minor hicups after S300 install - hints?
- Replies: 8
- Views: 4129
Minor hicups after S300 install - hints?
Just installed my S300 in a P28 and it works almost perfectly :) I have a B16A2 in an EG btw. Oem O2 sensor into oem pinout location, AEM uego into D10(ELD) However, if I use stockUsdmP30 or stockJdmP30 the car has an occasional "hicup" while driving and then SManager sometimes get unrespo...