Search found 12 matches
- Sat Sep 28, 2013 2:49 pm
- Forum: s300 / SManager
- Topic: RF interference freezes logs but move ecu 6-8 inches... ok
- Replies: 4
- Views: 2330
Re: RF interference freezes logs but move ecu 6-8 inches...
10-4. Will make the changes and report back.
- Sat Sep 28, 2013 7:52 am
- Forum: s300 / SManager
- Topic: RF interference freezes logs but move ecu 6-8 inches... ok
- Replies: 4
- Views: 2330
Re: RF interference freezes logs but move ecu 6-8 inches...
Running NGK bkr9eix. This is in an accord platform so it does not use the thermostat housing ground. On this platform that ground runs to the plenum. It is unmodified and connected. I have the battery relocated to the trunk. I run a ground directly from battery to the chassis in the trunk. Also a gr...
- Sat Sep 14, 2013 7:17 am
- Forum: s300 / SManager
- Topic: RF interference freezes logs but move ecu 6-8 inches... ok
- Replies: 4
- Views: 2330
RF interference freezes logs but move ecu 6-8 inches... ok
Ok so I am on an S300 with a p28 in an Accord. The ecu sits on the pass side floor in the factory position. Car has a pro10 ignition with T1 harness, pro10 box/ coil are up in front of the strut tower, running resistor plugs... etc. Have good grounds on the engine in multiple places, battery is in t...
- Thu Aug 01, 2013 7:03 pm
- Forum: s300 / SManager
- Topic: TPS min/ max scaling was slightly wrong...
- Replies: 2
- Views: 1704
Re: TPS min/ max scaling was slightly wrong...
That makes sense and would probably explain a minor stumbling issue that I recently noticed when cruising at a constant speed with very little throttle input.
- Thu Aug 01, 2013 4:22 pm
- Forum: s300 / SManager
- Topic: TPS min/ max scaling was slightly wrong...
- Replies: 2
- Views: 1704
TPS min/ max scaling was slightly wrong...
Ok I have only a basic understanding of tuning so far as I have always had my car tuned professionally out of state. That said, I am reading/ learning more every day so I am better informed and familiar with the management (an area I am lacking in). Stupid question time. I had previously scaled the ...
- Thu Aug 01, 2013 8:51 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1528103
Re: SManager software requests
IAT sensor re-scaling possible?
Would be a nice feature for those wanting to go to a GM type sensor.
Not sure if this a repeat question or already been addressed previously.
Would be a nice feature for those wanting to go to a GM type sensor.
Not sure if this a repeat question or already been addressed previously.
- Thu Sep 15, 2005 2:51 pm
- Forum: s100/s200
- Topic: clutch switch... did I mess up and hurt something?
- Replies: 2
- Views: 2099
- Thu Sep 15, 2005 12:49 pm
- Forum: s100/s200
- Topic: clutch switch... did I mess up and hurt something?
- Replies: 2
- Views: 2099
clutch switch... did I mess up and hurt something?
I hooked up the clutch switch real quick the other day and everything was all good. worked great and no problems... well today I go to change some of the rev points and before I even get that far, it does not even work anymore at all. hmm so thinking loose connection and disconnect the switch temp.....
- Thu Jul 14, 2005 4:14 pm
- Forum: Applications
- Topic: Hondata S300
- Replies: 27
- Views: 14869
- Wed Jul 13, 2005 7:40 am
- Forum: Applications
- Topic: Hondata S300
- Replies: 27
- Views: 14869
big thumbs up to you guys @ hondata on the s300! you really make a big move for the obd1 guys with this new system (usb and no burning chips esp.). :D I just bought an s2b not long ago but am glad to read here you will be offering romeditor v4 with iat and gear correction!!!! woot!!!! thinking about...
- Wed May 25, 2005 4:22 pm
- Forum: s100/s200
- Topic: interface cable or box problem?
- Replies: 2
- Views: 2056
- Fri May 20, 2005 7:06 pm
- Forum: s100/s200
- Topic: interface cable or box problem?
- Replies: 2
- Views: 2056
interface cable or box problem?
I just finished installing a p28 and the s200b... bump the key to the run position and I get a slow flashing red light. ok so I double and tripple check everything... my dealer burns me a new basemap to be sure and check the ecu over for continuity. everything looks good and I put it back in... flas...