are there any plans for this to be added in a future release
just so us full race guys can run spring pressure
avcr users and profec users can run spring pressure fine with out creep or boost loss across the rpm range
Search found 41 matches
- Sun Feb 24, 2008 10:18 pm
- Forum: K-Pro / KManager
- Topic: gain feature for boost by gear
- Replies: 1
- Views: 1684
- Tue May 01, 2007 4:34 am
- Forum: K-Pro Calibrations
- Topic: Just Installed KPRO in K20A2 and car stalls & idles poor
- Replies: 6
- Views: 6263
- Mon May 15, 2006 3:39 am
- Forum: K-Pro Calibrations
- Topic: k20a2 750 greddy tune?
- Replies: 1
- Views: 2746
k20a2 750 greddy tune?
okay i have a 2003 ep3 with a full type-s swap and im running the type-s greddy kit (yes the type-s one the piping runs differently and is a bit wider than the puny ep kit) well any way here is the deal i upgraded the injectors to 750's and im using the 650 tune with the injector trim set to 750cc t...
- Sun Mar 19, 2006 11:47 am
- Forum: K-Pro / KManager
- Topic: turbo k20 a2 trouble follows
- Replies: 1
- Views: 1615
turbo k20 a2 trouble follows
okay here it goes i had a motor swap done a couple weeks ago the motor was running flwlessly with the exception of an exhaust leak so this weekend i decided to bolt back up the trubo kit (greddy) after initial startup i tookit out for a drive after i felt that everything was good i got on it after a...
- Sat Mar 18, 2006 4:36 pm
- Forum: K-Pro / KManager
- Topic: Need help ASAP- VTEC issue
- Replies: 4
- Views: 2667
- Tue Feb 14, 2006 8:17 pm
- Forum: K-Pro / KManager
- Topic: k20z1 in an ep3?
- Replies: 1
- Views: 1860
k20z1 in an ep3?
i have the opurtunity to buy a 06 type -s swap with only 500 miles on it i drive an 03 si with a greddy turbo kit and kpro and i was looking for a k20a2 and stumbled across this z1 swap my question is the motor compatible with the 02-04 rsx/ep3 wiring on the engine side? i know the newer rsx's neede...
- Tue Nov 29, 2005 10:35 am
- Forum: K-Pro / KManager
- Topic: p1457 error code after boost by gear install
- Replies: 7
- Views: 5843
- Thu Nov 17, 2005 3:20 pm
- Forum: K-Pro / KManager
- Topic: K PRO K20A3 #4 misfire P0304 HELP
- Replies: 16
- Views: 8672
- Tue Nov 15, 2005 8:44 pm
- Forum: K-Pro / KManager
- Topic: K PRO K20A3 #4 misfire P0304 HELP
- Replies: 16
- Views: 8672
- Tue Nov 15, 2005 5:34 pm
- Forum: K-Pro / KManager
- Topic: p1457 error code after boost by gear install
- Replies: 7
- Views: 5843
- Tue Nov 15, 2005 4:31 pm
- Forum: K-Pro / KManager
- Topic: Version 1.2.1.1 bug
- Replies: 12
- Views: 5993
i have noticed with the things disabled for obd2 and the o2 sensors in older versions ltrim doenst respond at all and a af gauge wouldnt work (it would peg out) now with the new version and same parameters disabled everything works now l trim and my af guage is this a bug or was it redesinged to wor...
- Tue Nov 15, 2005 4:24 pm
- Forum: K-Pro / KManager
- Topic: p1457 error code after boost by gear install
- Replies: 7
- Views: 5843
p1457 error code after boost by gear install
i hooked up the gm solenoid to b21 on the ecu (as per instructions) after driving for a couple times i now get the p1457 error code on my return trip home even after restetting it so i looked in the ep3 service manuall and (pdf format) and searched for the code one of the tests for the evap cansiter...
- Thu Oct 27, 2005 11:21 am
- Forum: K-Pro / KManager
- Topic: will this work as a map sensor?
- Replies: 8
- Views: 4404
- Thu Oct 27, 2005 6:36 am
- Forum: K-Pro / KManager
- Topic: will this work as a map sensor?
- Replies: 8
- Views: 4404
the greddy saya it only reads to 43 psi (wouldnt that be a 3 bar then) it is just the voltage that is wrong and from what you told me there is a possibility that i can adjust the voltage so that the ecu will see this the same as the ones you recomend (just it would be too much trouble figuring it ou...
- Wed Oct 26, 2005 12:43 pm
- Forum: K-Pro / KManager
- Topic: will this work as a map sensor?
- Replies: 8
- Views: 4404
http://www.hondata.com/tech3barmap.html so if the voltage does match the requirements of the 3bar it will work so now my question is since this is a 4bar map sensor will the voltage be different comparing the two at the same boost level? like at 10 psi the 3bar will be at oh say 10vdc and the gredd...