Search found 16 matches
- Thu Sep 05, 2019 5:33 pm
- Forum: K-Pro / KManager
- Topic: D17 auto tune
- Replies: 4
- Views: 320
Re: D17 auto tune
I checked it was set 0-55 so I changed the setting, thanks I will try again
- Thu Sep 05, 2019 12:20 pm
- Forum: K-Pro / KManager
- Topic: Closed loop on start up HELP!!!!
- Replies: 8
- Views: 539
Re: Closed loop on start up HELP!!!!
I have the same issue the car acts funny trying to go in closed look but my innovate wideband isn't warm yet, Daniel from church automotive told me to limit the amount of short term correction the ecu can do but what works for me is if I turn the key on and let the sensor work up before I start the ...
- Thu Sep 05, 2019 11:23 am
- Forum: K-Pro / KManager
- Topic: D17 auto tune
- Replies: 4
- Views: 320
- Wed Sep 04, 2019 5:20 pm
- Forum: K-Pro / KManager
- Topic: D17 auto tune
- Replies: 4
- Views: 320
D17 auto tune
I tried to activate the auto tune while tuning a d17 with kpro but It wasn't working and I think its because the vtc is reading -20' is there a way to get that to read 0 so I can use the auto tune function?
- Tue Dec 12, 2017 6:10 pm
- Forum: K-Pro / KManager
- Topic: Datalogging input shaft rpm
- Replies: 2
- Views: 464
Re: Datalogging input shaft rpm
My kpro 4 has 20 inputs why can't you use one for that? I thought one is for a vss can't you sent that input?
- Tue Dec 12, 2017 1:57 pm
- Forum: K-Pro / KManager
- Topic: Datalogging input shaft rpm
- Replies: 2
- Views: 464
Datalogging input shaft rpm
I wanted to know if you can setup a sensor to data log the rpm on the transmission input shaft to determine if the clutch is slipping and mabye have a protection opting to let you know?
- Sat May 27, 2017 5:58 pm
- Forum: K-Pro / KManager
- Topic: readiness codes
- Replies: 1
- Views: 459
readiness codes
Can you add or is there a way to make it so the ecu gose through a normal prosses setting the readiness codes? I have a friend that took his cer to the refferie and the only resion he failed was because when the reff reset the computer and turned the ignition back on the readiness codes were clear i...
- Fri May 27, 2016 10:07 am
- Forum: K-Pro / KManager
- Topic: CAN output v4
- Replies: 6
- Views: 1837
Re: CAN output v4
Would it be able to output the correct format to use let's say a TSX cluster?
- Fri May 27, 2016 9:27 am
- Forum: K-Pro / KManager
- Topic: CAN output v4
- Replies: 6
- Views: 1837
Re: CAN output v4
The RDX rear diff usses the can bus to communicate with 4 other sensors and the PCM and abs unit
- Thu May 26, 2016 7:20 pm
- Forum: K-Pro / KManager
- Topic: CAN output v4
- Replies: 6
- Views: 1837
CAN output v4
Is it possible to use the CAN outputs on the digital input for a factory honda CAN bus?
- Fri May 13, 2016 4:18 pm
- Forum: FlashPro Manager
- Topic: TSX 07-08 flash pro for auto
- Replies: 3
- Views: 1044
Re: TSX 07-08 flash pro for auto
Have you guys ever typed using a Tsx computer in an element?
- Fri May 13, 2016 3:51 pm
- Forum: FlashPro Manager
- Topic: TSX 07-08 flash pro for auto
- Replies: 3
- Views: 1044
TSX 07-08 flash pro for auto
I want to jnwo if you can adjust the shift points of the transmission using flashpro to get more rpms out of the engine with a built engine????
- Mon May 09, 2016 3:13 pm
- Forum: K-Pro / KManager
- Topic: KPro / KManager requests
- Replies: 121
- Views: 48753
Re: KPro / KManager requests
DBW support for traction control? I know not a complicated this to ad but the biggest thing is the console from the kpro after you wire the console unit TB and throttle sensor
Is this possible?
Is this possible?
- Tue May 03, 2016 1:48 pm
- Forum: K-Series Reflash
- Topic: Bad ECU with reflash
- Replies: 3
- Views: 4355
Re: Bad ECU with reflash
Dose it make any difference that the I purchased the reflashed i didn't buy the computer from someone with the reflashed?
- Tue May 03, 2016 1:33 pm
- Forum: K-Series Reflash
- Topic: Bad ECU with reflash
- Replies: 3
- Views: 4355
Bad ECU with reflash
I have a prb ECU that has a hondata reflashed on it but the computer its self is bad. It won't move the vtc at all and gives me a p0011. I have tested the car with kpro and a stock computer plus I have data logged all computers with my HIM USING HDS software so I'm 100% it's bad. What I need is to l...