Search found 8 matches
- Sun Oct 15, 2017 9:26 pm
- Forum: s300 / SManager
- Topic: Vtec conversion
- Replies: 2
- Views: 1550
Re: Vtec conversion
And I noticed for the vtec conversion instructions there are a couple versions: http://www.xenocron.com/install/1980.htm Is this the correct version, since I don't have IABs? http://forum.pgmfi.org/viewtopic.php?t=5664 Should I disregard this thread? It says it's for vtec and IABs. I noticed it's mo...
- Sun Oct 15, 2017 9:05 pm
- Forum: s300 / SManager
- Topic: Vtec conversion
- Replies: 2
- Views: 1550
Vtec conversion
Hey I have a P75 ecu with the 1980 board in my LS Vtec turbo crx. I ordered the vtec conversion components and had them soldered in. The only part I am unsure about is where I will wire the vtec solenoid and oil switch into. Will I just use the P28 locations? Thanks! A4 vtec solenoid D6 oil pressure...
- Tue Oct 03, 2017 8:40 am
- Forum: S300 Calibrations
- Topic: LS Vtec Turbo
- Replies: 1
- Views: 1745
LS Vtec Turbo
Hey I have a LS Vtec w/ B16 head, gsr cams, 8.5 JE Pistons, 81.5 bore, ID 1000 injectors, 4 port boost controller, OMNI 4 bar map, and Garrett GTX2860r
I'm looking for a basemap to get me driving up to where I can dyno tune! Thank you!
I'm looking for a basemap to get me driving up to where I can dyno tune! Thank you!
- Wed Jan 20, 2016 9:54 am
- Forum: s300 / SManager
- Topic: fuel pump not priming
- Replies: 5
- Views: 2532
Re: fuel pump not priming
Well I for now just wired my fuel pump up to an acc source. It runs and drives now, just needs a tune. Though I still need to figure out why the fuel pump relay isn't getting voltage. I checked the main relay harness according to the manual and pin 4(blue/white) gets no voltage, and ign switch fuse(...
- Tue Jan 19, 2016 2:53 pm
- Forum: s300 / SManager
- Topic: fuel pump not priming
- Replies: 5
- Views: 2532
Re: fuel pump not priming
I just stuck my old ecu back in and turned the key, my fuel pump kicked right on. so it seems like my issues is something with the ecu or it's jumper harness. Can anyone give me some advice? Anyone know what pin I could check for the output? I tried starting it while I had some pressure left in the ...
- Tue Jan 19, 2016 12:10 pm
- Forum: s300 / SManager
- Topic: fuel pump not priming
- Replies: 5
- Views: 2532
Re: fuel pump not priming
Looks like pin 4(starter switch) in the main relay is getting no power. I'll need to trace it back and see if it's not getting power from ecu or what. I found all my grounds, all look good.
- Tue Jan 19, 2016 10:32 am
- Forum: s300 / SManager
- Topic: fuel pump not priming
- Replies: 5
- Views: 2532
Re: fuel pump not priming
Yeah that's for sure. From some research looks like it could be my thermostat ground, sounded like a lot of people had exact same issue. Only I don't see it anywhere, not sure if a previous owner re-positioned it or what. Time to hunt for it. And looks like my sensors are working, just needed to ena...
- Tue Jan 19, 2016 4:08 am
- Forum: s300 / SManager
- Topic: fuel pump not priming
- Replies: 5
- Views: 2532
fuel pump not priming
Hello, I just converted my obd0 90 crx with a turbo ZC to obd1 hondata. It ran great before swapping out, but now it's not starting. Looks like I have spark but no fuel. My fuel gauge is at 0 and I don't hear the pump prime like it used to. Are my sensors supposed to read real-time on SManager? My c...