Search found 20 matches

by sean
Sun Feb 07, 2016 7:38 pm
Forum: RDX 2007-2012
Topic: New injectors
Replies: 6
Views: 13787

Re: New injectors

No, not on any forms...still woring out problems...would like the car to be done properly before I post it up on acurazine...so far mods are 3.5" downpipe, into a 3 inch exhaust to muffler ( heat wrapped ). 850 cc injectors, cold air intake ( a massive one ) and a front mount....noticeable differenc...
by sean
Tue Sep 15, 2015 5:12 pm
Forum: RDX 2007-2012
Topic: New injectors
Replies: 6
Views: 13787

Re: New injectors

Ok, I'm definitely going to get it tuned but I was going to consider a dyno tune, if you can make a tune that will help make the car run better than I am all ears , it would be a temp fix until I go to the dyno Problems - rough idle...especially when AC is on - s trim at idle is 5-10%....with a 14.6...
by sean
Sun Sep 13, 2015 12:14 pm
Forum: RDX 2007-2012
Topic: New injectors
Replies: 6
Views: 13787

Re: New injectors

Hey so Iv downloaded the hondata RDX-2007-9K&NCAI-600CCDW tune and I just changed the injector calibration from 600cc to 850cc injectors. The car ran fairly strong....noticeable difference from before even if i did not push it past 30% throttle, Iv uploaded my datalog just me going around the block,...
by sean
Sat Sep 12, 2015 7:00 am
Forum: RDX 2007-2012
Topic: New injectors
Replies: 6
Views: 13787

New injectors

Hello,
by sean
Sun Aug 23, 2015 8:51 pm
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

im sure that iv mentioned earlier in this post that I set my speed limit to 25mph or something like that...and it is uploading correctly....if you take a look at the message i posted earlier...do all of these values correspond to a proper tune?
by sean
Fri Aug 14, 2015 3:56 pm
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

Alright, So Iv Dataloged my car...Ill describe some of the values I have while running my car in second gear WOT from 12MPH to 72MPH I make MAX boost at around 3200RPM at 15.2PSI. There are a couple of values I do not understand like AFM and AFM.c I also do not understand why the actual VTC cam angl...
by sean
Fri Aug 07, 2015 8:27 pm
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

I think you're chasing the wrong thing. The calibration on the FlashPro is dyno tuned. If you don't think you have any gains then you should do back to back dynos, and then tune / fix any problems. Is there anything that would impair a tune from working properly? I have changed my O2 sensor recentl...
by sean
Fri Aug 07, 2015 1:53 pm
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

Spunkster wrote:The calibrations in the FlashPro are not the same as the reflash available by sending in the ECU.
Is there anyway I can get a copy of this software? The tuned software offered for free online in my opinion doesn't seem to give me any gain in performance
by sean
Fri Aug 07, 2015 4:31 am
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

pepperdanky wrote:If you look under 'Rev Limits' for that calibration, the limiter is set to 6900 rpm.

Yup , it is.....is the tuned calibration just a base calibration to get me to the dyno, or is it identical to the one offered by hondata if I send my ecu out.
by sean
Thu Aug 06, 2015 10:19 am
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

If you look under 'Rev Limits' for that calibration, the limiter is set to 6900 rpm. Yup, it is....what I want to know is the tune that I have on my flashpro the same as the one offered by hondata by sending out my ecu, or is it just a base calibration that I need to go to a dyno to fine tune?? Tha...
by sean
Wed Aug 05, 2015 5:45 pm
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

So I was able to limit my speed to 35MPH so i know my computer is interacting with the flashpro step by step -open laptop and flashpro software -plug flashpro into computer -plug flashpro into OBD port -select "new calibration" on flashpro software -select RDX-2007-2-TUNED 410CC US RDX 2007, stock t...
by sean
Tue Jul 28, 2015 10:11 am
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

Yeah I've tried everything I could to get it to load....no Bueno
by sean
Mon Jul 27, 2015 7:46 pm
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

Don't upload the calibration stored on the FlashPro, instead, just click on the upload arrow at the top of the FlashPro software. ok, how will i know this is the right tune for me? Im just going to open my laptop...plug the flashpro to my laptop and OBD port and once all the green presss the upload...
by sean
Fri Jul 24, 2015 4:57 pm
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

How are you uploading the calibration? ie what button or menu item are you pressing? In FlashProManager after an upload in the FlashPro window does it show the calibration is stock or not stock? Can you use the 'send support information to Hondata' function from the help menu, with everything plugg...
by sean
Fri Jul 24, 2015 8:48 am
Forum: RDX 2007-2012
Topic: Flash pro not downloading to ecu
Replies: 28
Views: 9588

Re: Flash pro not downloading to ecu

ok in sent the support information

Thanks for the quick replies