Search found 22 matches

by steve47co1
Sun Jul 26, 2015 10:16 am
Forum: FlashPro Manager
Topic: How hackable are Flashpro/Honda ECU's?
Replies: 2
Views: 1808

Re: How hackable are Flashpro/Honda ECU's?

Thanks for the reply. Comforting.

I did read that some hackers were hacking into cars through the ECU; hence the reason for my question.
by steve47co1
Sat Jul 25, 2015 7:45 am
Forum: FlashPro Manager
Topic: How hackable are Flashpro/Honda ECU's?
Replies: 2
Views: 1808

How hackable are Flashpro/Honda ECU's?

Given the revelation that surfaced this week with Fiat/Chrysler vehicles, the automaker is recalling 1.4 million vehicles (http://www.autoguide.com/auto-news/2015/07/fiat-chrysler-recalls-1-4m-vehicles-over-hacking-concerns.html, how hackable are Honda ECU's that have been tuned with FlashPro? NOTE:...
by steve47co1
Wed Jul 01, 2015 1:04 pm
Forum: FlashPro Manager
Topic: Correct unit selection for measuring boost psi in FP
Replies: 7
Views: 1679

Re: Correct unit selection for measuring boost psi in FP

Got it. As suggested, use "/psi and the MAP window in FP display will show vacuum numbers (-) until you increase throttle, then it will show atmospheric pressure (+) numbers.
by steve47co1
Mon Jun 22, 2015 8:56 am
Forum: FlashPro Manager
Topic: Correct unit selection for measuring boost psi in FP
Replies: 7
Views: 1679

Re: Correct unit selection for measuring boost psi in FP

Then I surmise I need to customize/add another window to the FP display to show psi, because MAP shows negative numbers now and there is no other window that would show psi? Am I on track?
by steve47co1
Mon Jun 22, 2015 6:55 am
Forum: FlashPro Manager
Topic: Correct unit selection for measuring boost psi in FP
Replies: 7
Views: 1679

Re: Correct unit selection for measuring boost psi in FP

Basic question, then; is it possible to see boost numbers accurately in FlashPro manager or do I have to interpolate?
by steve47co1
Sun Jun 21, 2015 9:22 am
Forum: FlashPro Manager
Topic: Correct unit selection for measuring boost psi in FP
Replies: 7
Views: 1679

Re: Correct unit selection for measuring boost psi in FP

Thanks, Hondata; tried that and I get negative numbers in the MAP window?
by steve47co1
Sat Jun 20, 2015 5:23 pm
Forum: FlashPro Manager
Topic: Correct unit selection for measuring boost psi in FP
Replies: 7
Views: 1679

Correct unit selection for measuring boost psi in FP

I am using FlashPro with the latest software and firmware and I have the Hondata 4 bar sensor installed. (I also have the CT-e SC Stage 2 kit installed with the 3.15" pulley and 1000cc injectors.) I make the 4 bar selection under sensors and indicate "psi" under measurement unit for MAP window. When...
by steve47co1
Thu Mar 05, 2015 6:43 pm
Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
Topic: Gas mileage drop?
Replies: 3
Views: 2707

Re: Gas mileage drop?

You were right. Very negative fuel trim; running super rich at WOT. My tuner sent me a revised map; I will data log tomorrow and see what it looks like.

Thank you.
by steve47co1
Thu Mar 05, 2015 10:43 am
Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
Topic: Gas mileage drop?
Replies: 3
Views: 2707

Re: Gas mileage drop?

Thank you, Hondata! I will look into that.
by steve47co1
Wed Mar 04, 2015 2:02 pm
Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
Topic: Gas mileage drop?
Replies: 3
Views: 2707

Gas mileage drop?

I have been getting very consistent gas mileage since 10/13 when my 12 Civic Si was last tuned on a dyno. On the highway, it was not hard to get 34mpg and 31 city (calculated). Now, since I had to clean the water out of my gas tank, fuel lines, fuel filter, injectors, etc., my gas mileage has droppe...
by steve47co1
Sun Mar 01, 2015 12:41 pm
Forum: FlashPro Manager
Topic: Stumped in Colorado
Replies: 11
Views: 2314

Re: Stumped in Colorado

I had access to the Honda Data System scanner for the OBDII port, but, even though we tried several times, it would never relearn. I did find out that Clutch Masters has a clutch for 9thGen that doesn't trip the crank position sensor.
by steve47co1
Fri Feb 27, 2015 8:10 am
Forum: FlashPro Manager
Topic: How to set up Injectors size in FP manager for correct MPG calculation ?
Replies: 8
Views: 2973

Re: How to set up Injectors size in FP manager for correct MPG calculation ?

Mabo,

I am interested in the reply to this, too! I have the same problem.
by steve47co1
Tue Feb 24, 2015 8:02 am
Forum: FlashPro Manager
Topic: Stumped in Colorado
Replies: 11
Views: 2314

Re: Stumped in Colorado

Thank you, pepperdanky; this issue is well documented once you know what you are looking for! ajpturbopittsburgh - to disable misfire codes, connect FP Manager; go to calibration tab, miscellaneous, and you will see "disable misfire codes." As I understand it, though, this does not apply to 8th Gen ...
by steve47co1
Mon Feb 23, 2015 12:39 pm
Forum: FlashPro Manager
Topic: Stumped in Colorado
Replies: 11
Views: 2314

Re: Stumped in Colorado

SOLVED. If you install an aftermarket lightweight clutch, be sure to (1) have FlashPro, and (2) disable misfire codes under the calibration tab on the main screen. Postmortem; I had two problems; the first was water in the fuel tank and then I compounded it by installing the new clutch and flywheel,...
by steve47co1
Mon Feb 23, 2015 11:38 am
Forum: FlashPro Manager
Topic: Stumped in Colorado
Replies: 11
Views: 2314

Re: Stumped in Colorado

I think I have the answer to my problem...........typed in Flashpro and misfire codes in Google; came up with a lot of information. When you put in a different weight flywheel (aftermarket), you have to disable misfire codes in FlashPro in the calibration screen. Going to check it now and will get b...