bump
My situation is a bit different from the OP. I don't have my original 04 ECU so I will need to buy a used one. Will the dealer still be able to do ecu - immobilizer sync process if I left the adapter in?
Search found 8 matches
- Wed Mar 11, 2015 11:16 pm
- Forum: TSX 2004-2014
- Topic: Going back to stock re: CAN adapter
- Replies: 4
- Views: 4078
- Sat Apr 05, 2014 9:26 am
- Forum: Hondata Mobile
- Topic: iOS 7 and flashpro bluetooth
- Replies: 8
- Views: 5802
Re: iOS 7 and flashpro bluetooth
The problem is the flashpro does not even show up in the iOS bluetooth menu. It won't (what step above is that?) It will only show on the roqyBT7 bluetooth list. You should not need to change the OBD-II data port. I have build 4025 and it works. I see that the hondata mobile page has been updated t...
- Sat Apr 05, 2014 8:19 am
- Forum: Hondata Mobile
- Topic: iOS 7 and flashpro bluetooth
- Replies: 8
- Views: 5802
Re: iOS 7 and flashpro bluetooth
You realize that at this point we do not have Hondata Mobile available for iOS? In that case, I assume that you are trying to use roqyBT7 on a jail broken iPhone. What works for me: 1. Make sure the FlashPro pin is 1234 2. Switch off bluetooth from iPhone settings and clear all apps from memory. 3....
- Fri Apr 04, 2014 6:27 pm
- Forum: Hondata Mobile
- Topic: iOS 7 and flashpro bluetooth
- Replies: 8
- Views: 5802
iOS 7 and flashpro bluetooth
Is iOS 7 suppose to be able to connect to the flashpro via bluetooth natively because the only way I can get my phone to connect is via a jailbreak program roqyBT7. The flashpro doesn't even show up in the iOS bluetooth menu. I can't seem to get the latest version of dash command to work either sinc...
- Fri Jan 17, 2014 1:25 pm
- Forum: TSX 2004-2014
- Topic: flashpro harness adapter
- Replies: 6
- Views: 4551
Re: flashpro harness adapter
Went ahead to the dealer and they were successful in pairing the ecu and immobilizer. Also was able to upload calibrations to the ecu no problems. One minor issue was I had to reprogram my remote starter immobilizer bypass module (PKH3) afterwards. Remote starting the car only resulted in a crank bu...
- Thu Jan 16, 2014 6:47 pm
- Forum: TSX 2004-2014
- Topic: flashpro harness adapter
- Replies: 6
- Views: 4551
Re: flashpro harness adapter
Thanks. Got the harness installed and flashpro seems to recognize the used 07 ECU correctly. At this point, the dealer shouldn't have any problems pairing it to my immobilizer right?Spunkster wrote:that is correct.
- Tue Jan 14, 2014 11:35 am
- Forum: TSX 2004-2014
- Topic: flashpro harness adapter
- Replies: 6
- Views: 4551
Re: flashpro harness adapter
So the harness must be connected to the green junction connector? Not even spliced into the can wires right at the ecu connector E plug?
- Mon Jan 13, 2014 11:06 pm
- Forum: TSX 2004-2014
- Topic: flashpro harness adapter
- Replies: 6
- Views: 4551
flashpro harness adapter
The instructions say to plug the flashpro harness into the green connector located in the top left area of the glovebox but the connector is in a really tight location and hard to get to. My question is, can I solder the harness to the CAN high/low wires found behind the gauge cluster instead?