Search found 23 matches
- Sat Apr 15, 2023 10:48 am
- Forum: Fit 2007-2008
- Topic: 2008 Fit MT HKS turbo kit WOT Lambda adjustment tables
- Replies: 5
- Views: 3060
Re: 2008 Fit MT HKS turbo kit WOT Lambda adjustment tables
I reread your post again and just wanted to hit a couple more points you may be unclear on. 1.) WOT window pressure can be adjusted as well as the other parameters that need to be met to activate the switchover from closed to open loop. 2.) Closed loop target AFR is done in the closed loop tab IIRC ...
- Sat Apr 15, 2023 9:46 am
- Forum: Fit 2007-2008
- Topic: 2008 Fit MT HKS turbo kit WOT Lambda adjustment tables
- Replies: 5
- Views: 3060
Re: 2008 Fit MT HKS turbo kit WOT Lambda adjustment tables
Actually the OEM WB sensor is very accurate... Really only reason for separate WB is to verify the reading. Reading off the same exhaust port they are within .1to .2 AFR (negligible)of reading exactly the same in my logs (AEM UEGO analog WB). The WOT target table is used for lambda overlay in the fu...
- Tue Nov 16, 2021 8:36 pm
- Forum: RDX 2007-2012
- Topic: 1st Gen RDX Autotune
- Replies: 20
- Views: 5944
Re: 1st Gen RDX Autotune
RaH, sorry I didn't see that you have replied and don't check here often, I have also not done any attempts to get speed density working as I haven't had the time. As to your post " I see target as rich as .69 lambda", yes you probably are seeing that as the target which equals 10.14 AFR a...
- Mon Oct 18, 2021 7:54 pm
- Forum: RDX 2007-2012
- Topic: 1st Gen RDX Autotune
- Replies: 20
- Views: 5944
Re: 1st Gen RDX Autotune
Haha. Well firstly thank you for your honest input. I have decided to unlock the rdx from the pro and give it to my wife to drive and get a cheap 05 06 accord with the k24 manual. Since the rdx has so much limitations and lack of support and rnd, i am gonna just pass on this project. Its a unicorn ...
- Mon Oct 18, 2021 1:50 pm
- Forum: RDX 2007-2012
- Topic: 1st Gen RDX Autotune
- Replies: 20
- Views: 5944
Re: 1st Gen RDX Autotune
LOL at least you got further than I did with getting a response by the person I wanted to ACTUALLY hear from... PM me as maybe we can get this worked out. I was working with Jeff Evans in a way, as I purchased his Evans Performance Academy training video access so he was responding in the RDX video ...
- Sat Aug 21, 2021 4:05 pm
- Forum: RDX 2007-2012
- Topic: Change MAF to MAP based calibration
- Replies: 8
- Views: 3280
Re: Change MAF to MAP based calibration
https://i.imgur.com/Cr7gK0i.jpg This is from Evans Performance Academy video specifically on setting up the RDX on speed/density, showing to have the AFM unchecked as well as he states this in the video but to only have the "use MAP fuel tables" box checked. https://i.imgur.com/YYWLHkS.pn...
- Wed Aug 18, 2021 5:37 pm
- Forum: RDX 2007-2012
- Topic: Change MAF to MAP based calibration
- Replies: 8
- Views: 3280
Re: Change MAF to MAP based calibration
I would recommend that you contact a tuner to help you tune this properly using the MAP based tuning and this will also ensure that it is running safely and get the most power out of it. That is not what I asked. I am asking your to clearly outline the steps to enable the calibration to run off the...
- Wed Aug 18, 2021 4:24 pm
- Forum: RDX 2007-2012
- Topic: Change MAF to MAP based calibration
- Replies: 8
- Views: 3280
Re: Change MAF to MAP based calibration
I'm asking about disabling the AFM just to see if it will start and run with them disabled. If it runs using just the AFM, then it sounds like a tuning issue. I would recommend taking it to a good tuner that is familiar with tuning these on the dyno. 1.) I had no luck, attached is the Calibration a...
- Tue Aug 17, 2021 7:05 pm
- Forum: RDX 2007-2012
- Topic: Change MAF to MAP based calibration
- Replies: 8
- Views: 3280
Re: Change MAF to MAP based calibration
What happens if you disable the AFM? Will it start with MAP tables disabled and only with AFM enabled? 1.) It is stated in flashpro manager to keep AFM enabled and specifically states "Do not disable or remove AFM". I have both boxes checked one for "AFM enabled" and also for &q...
- Mon Aug 16, 2021 8:20 pm
- Forum: RDX 2007-2012
- Topic: Change MAF to MAP based calibration
- Replies: 8
- Views: 3280
Change MAF to MAP based calibration
Hello, having issue switching the calibration to MAP based fueling and getting the vehicle to run. 2008 RDX only modification is DIY cold air intake 3" tubing and MAF sensor in stock location. Starting calibration is "stock tuned" option provided for upload. Enabled the MAP check box ...
- Fri Jun 11, 2021 3:47 pm
- Forum: Fit 2007-2008
- Topic: Can't edit columns/rows for DBW in flashpro software
- Replies: 5
- Views: 3490
- Fri Jun 11, 2021 3:33 pm
- Forum: Fit 2007-2008
- Topic: Can't edit columns/rows for DBW in flashpro software
- Replies: 5
- Views: 3490
Re: Can't edit columns/rows for DBW in flashpro software
Sorry, no. For legal reasons we don't allow the indexes to be altered. I totally understand from a legal standpoint why you would want to lock these columns/rows. My issue/questions are I have a custom fabricated extremely short and larger dia runner intake manifold with 5mm lager (R18) TB for the ...
- Fri Jun 11, 2021 2:29 pm
- Forum: Fit 2007-2008
- Topic: Plx Wide-band ecu pin output reference
- Replies: 6
- Views: 15917
Re: Plx Wide-band ecu pin output reference
Hondata Rep, going through the service manual this is what I see for EGR 6pin connector:function name/(wire color)/ECM connector location. 123 <-This would represent the 6PIN as it is shown in the service manual 4/6 1=EGRP/(WHT/BLK)/B12 2=SG2/(GRN/BLK)/A23 3=VCC2/(YEL/BLU)/A20 4=EGR/(PNK)/B16 6=PG1...
- Fri Jun 11, 2021 1:45 pm
- Forum: Fit 2007-2008
- Topic: Can't edit columns/rows for DBW in flashpro software
- Replies: 5
- Views: 3490
Re: Can't edit columns/rows for DBW in flashpro software
So what would happen with higher RPM? reference 7k row?
- Fri Jun 11, 2021 12:45 pm
- Forum: Fit 2007-2008
- Topic: Can't edit columns/rows for DBW in flashpro software
- Replies: 5
- Views: 3490
Can't edit columns/rows for DBW in flashpro software
Hello, can we get an update to be able to edit/make use of the redundant columns for more DBW resolution? And edit the rows for higher than 7k RPM?