Search found 17 matches
- Mon Sep 25, 2006 4:31 am
- Forum: s300 / SManager
- Topic: Typical IAT JRSC??
- Replies: 9
- Views: 5081
The air temp will be high if you removed/not used the jrsc supplied relay. The relay only works to fool the ecu into thinking the temp is lower (cold) than it actually is so that the ecu increases fuel delivery (rich mixture). It is a mechanical hack that should not be used with a programmable ecu....
- Mon Aug 21, 2006 11:45 pm
- Forum: s300 / SManager
- Topic: Wideband and launch control question.
- Replies: 6
- Views: 4120
Re: another question
I think it would be bad, because it is leaning out without fuel. This leaning out would cause cylinder temps to climb, and in turn could cause the pistons to expand and score the walls. Could this happen with a fuel cut rev limit, or is it not that dramatic to cause any damage, thats my question Th...
- Thu Aug 17, 2006 1:57 pm
- Forum: s300 / SManager
- Topic: PLX and capacitor
- Replies: 9
- Views: 6214
- Wed Aug 16, 2006 10:19 pm
- Forum: s300 / SManager
- Topic: PLX and capacitor
- Replies: 9
- Views: 6214
- Tue Aug 15, 2006 9:04 pm
- Forum: s300 / SManager
- Topic: PLX and capacitor
- Replies: 9
- Views: 6214
- Mon Aug 14, 2006 10:13 am
- Forum: s300 / SManager
- Topic: converting your v 1.15 files to 1.16
- Replies: 7
- Views: 3649
There is no problem...that is just how they show up. They are old Romeditor V3 bin files that have been converted for use with teh s300. Don't change the injector size, just leave it however it shows up. In that case, what do you do if you want to upgrade to 550 injectors on the B18C? Also, why was...
- Sun Aug 13, 2006 12:30 am
- Forum: s300 / SManager
- Topic: converting your v 1.15 files to 1.16
- Replies: 7
- Views: 3649
- Wed Aug 02, 2006 8:25 pm
- Forum: s300 / SManager
- Topic: PLX and capacitor
- Replies: 9
- Views: 6214
- Wed Aug 02, 2006 1:44 am
- Forum: s300 / SManager
- Topic: PLX and capacitor
- Replies: 9
- Views: 6214
PLX and capacitor
I've got a PLX M300 ready for install now and I'm wondering if the included caps are necessary for this application (w/ S300j)? I've searched the forums and not seen any mention of this...
- Mon Jul 10, 2006 6:09 am
- Forum: s300 / SManager
- Topic: How do I wire in my Wideband?
- Replies: 25
- Views: 12159
- Wed Jun 07, 2006 6:30 pm
- Forum: s300 / SManager
- Topic: Tuners in Toronto area?
- Replies: 1
- Views: 1495
Tuners in Toronto area?
Hello
I'm looking for a good tuner in the Toronto area for a Hondata S300.
Any suggestions?
I'm looking for a good tuner in the Toronto area for a Hondata S300.
Any suggestions?
- Fri Jun 02, 2006 4:33 pm
- Forum: S300 Calibrations
- Topic: B18Csupercharger 12 ohm 440 injectors
- Replies: 8
- Views: 30587
- Wed May 24, 2006 5:05 pm
- Forum: s300 / SManager
- Topic: About Jackson racing Hondata MAP sensor spacer
- Replies: 11
- Views: 6693
- Fri Dec 03, 2004 4:52 pm
- Forum: s100/s200
- Topic: S200 hondata - P72 Ecu Socketing Trouble
- Replies: 10
- Views: 5836
I've been having the same problem with my P72J socketed by Payn Technologies: flashing light on blue box and car in limp mode. Runs fine when mechanicals set to stock and J1 cut (have a CEL for knock sensor only). Sent it back to Payn and they had it for MONTHS! Supposedly they tested it and could f...
- Sat Jul 31, 2004 8:14 am
- Forum: s100/s200
- Topic: Trouble with JRSC JDM B18C and Hondata S200b - Advice?
- Replies: 2
- Views: 2265
Trouble with JRSC JDM B18C and Hondata S200b - Advice?
I'm having major problems with this system. I purchased an S200b system from Payn Tech 3 months ago and it has never worked. Payn sent out my P72J ecu for chipping and then sent it back without testing first. When installed, the car ran like crap with RC440s and the red light on the blue box was fla...