Search found 22558 matches
- Mon Mar 18, 2024 11:36 am
- Forum: FlashPro Calibrations
- Topic: basemap download help for a newbie!
- Replies: 2
- Views: 55
Re: basemap download help for a newbie!
Close all instances of FlashPro manager running and the only open one copy.
- Mon Mar 18, 2024 11:29 am
- Forum: K-Pro / KManager
- Topic: VCC3 for 5 volt reference
- Replies: 1
- Views: 41
Re: VCC3 for 5 volt reference
I would recommend tapping the wire.
This cannot be done on the v1 s300.
This cannot be done on the v1 s300.
- Mon Mar 18, 2024 11:27 am
- Forum: s300 / SManager
- Topic: Upload botton grayed out can't upload
- Replies: 1
- Views: 68
Re: Upload botton grayed out can't upload
There appears to be a jumper on J12 and it must be removed.
- Fri Mar 15, 2024 4:14 pm
- Forum: FlashPro Manager
- Topic: Switching from ktuner
- Replies: 3
- Views: 7264
Re: Switching from ktuner
With everything plugged in and the ignition in the on position, go to the Help menu and click on “send feedback”. Include a detailed description of the issue.
Post the FlashPro serial number here.
Post the FlashPro serial number here.
- Thu Mar 14, 2024 12:23 pm
- Forum: FlashPro Calibrations
- Topic: K24A swap ignition question
- Replies: 1
- Views: 51
Re: K24A swap ignition question
It should not matter which ones are used.
- Thu Mar 14, 2024 9:42 am
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: ECU "FORGETTING" FLASH
- Replies: 3
- Views: 101
Re: ECU "FORGETTING" FLASH
answered via email
- Thu Mar 14, 2024 8:59 am
- Forum: Civic Si 2012-2015 US/Canadian / 2013+ ILX
- Topic: ECU "FORGETTING" FLASH
- Replies: 3
- Views: 101
Re: ECU "FORGETTING" FLASH
When it does this have you tried datalogging to see what errors are reported?
- Thu Mar 14, 2024 8:57 am
- Forum: K-Pro / KManager
- Topic: Kpro v4 Not Firing Injectors
- Replies: 2
- Views: 59
Re: Kpro v4 Not Firing Injectors
Have you tried your ECU on a different vehicle to see if it starts and runs that ok?
- Wed Mar 13, 2024 9:05 am
- Forum: K-Pro / KManager
- Topic: NC/NS
- Replies: 1
- Views: 56
Re: NC/NS
You need to try the ECU in a known working vehicle and see if it works. If it doesn't then something in your vehicle has damaged the ECU. If it does work, then there is most likely a wiring problem in your vehicle.
- Tue Mar 12, 2024 2:33 pm
- Forum: K-Pro Calibrations
- Topic: 06 Rsx-s help
- Replies: 3
- Views: 109
Re: 06 Rsx-s help
You can try contacting the original owner, but there is no other way to get the file you overwrote.
- Tue Mar 12, 2024 9:03 am
- Forum: s300 / SManager
- Topic: Wideband Questions
- Replies: 8
- Views: 220
Re: Wideband Questions
For power I would recommend that you use a switched power source in the fuse box under the dash as there are empty slots you can connnect a spade connector to that are switched with the ignition.
Try it without the analog signal ground and see if it reads correctly.
Try it without the analog signal ground and see if it reads correctly.
- Tue Mar 12, 2024 8:58 am
- Forum: K-Pro / KManager
- Topic: VSS in an AUTO rsx ecu.
- Replies: 12
- Views: 233
Re: VSS in an AUTO rsx ecu.
You do not have the alternate input set in the calibration as you need to when using an Auto ECU.
Make sure you follow the instructions at: https://hondata.com/tech-alternative-ecu-engine-swap
Make sure you follow the instructions at: https://hondata.com/tech-alternative-ecu-engine-swap
- Tue Mar 12, 2024 8:55 am
- Forum: K-Pro / KManager
- Topic: RSX Speedometer Problems
- Replies: 12
- Views: 1864
Re: RSX Speedometer Problems
Send an email to support <at> hondata.com with the following and I will issue an RMA and give you further instructions:
Name:
Address:
Phone:
Email:
Serial#:
Description of problem:
Include a link to this thread.
Name:
Address:
Phone:
Email:
Serial#:
Description of problem:
Include a link to this thread.
- Mon Mar 11, 2024 2:27 pm
- Forum: K-Pro / KManager
- Topic: speedometer reads, but no vss on kpro (PRB)
- Replies: 7
- Views: 123
Re: speedometer reads, but no vss on kpro (PRB)
We test on a bench, but not everything is tested as we are making sure that the K-Pro uploads and datalogs properly. It was also installed over a year and a half ago.
- Mon Mar 11, 2024 12:02 pm
- Forum: s300 / SManager
- Topic: Wideband Questions
- Replies: 8
- Views: 220
Re: Wideband Questions
For the wideband to read correctly and be able to be used for closed loop you must use the D10 input as the D14 input cannot see the full voltage range. Details can be found in the help file at: https://hondata.com/help/smanager/widebandlambdaparameters.htm?zoom_highlightsub=wideband The other senso...