Search found 18 matches
- Tue Nov 28, 2023 9:17 am
- Forum: K-Pro / KManager
- Topic: Can't upload tune - registration required
- Replies: 3
- Views: 1286
- Wed Nov 22, 2023 9:11 pm
- Forum: K-Pro / KManager
- Topic: Can't upload tune - registration required
- Replies: 3
- Views: 1286
Can't upload tune - registration required
tried to use this ecu and it said needed to update drivers and kpro software (from current to beta) then it said i needed to register before uploading. same as the earlier posts but all green in info panel and otherwise everything in the software looks ok (on line, drivers installed, no locks) i eve...
- Fri Oct 22, 2021 3:04 pm
- Forum: K-Pro / KManager
- Topic: CAMCMD reads 0 but map says otherwise
- Replies: 2
- Views: 840
Re: CAMCMD reads 0 but map says otherwise
yep we found a part of the harness was not secured and it rubbed through a wire on the water neck and it was shorting, causing the ecu to reset. When moving the throttle body we found it would hiccup and as we tugged on the harness it was priming the fuel pump over and over again. wrapped it and sec...
- Mon Oct 18, 2021 7:35 pm
- Forum: K-Pro / KManager
- Topic: CAMCMD reads 0 but map says otherwise
- Replies: 2
- Views: 840
CAMCMD reads 0 but map says otherwise
In the attached datalog you can see the first 2.5 minutes the cam angles are doing as intended, then in 2:50.5 the VSS and CAM blip and go to 0, then immediately after the same thing happens (we are troubleshooting, the car has suddenly started falling on its face like lean/boost cut, also artifacts...
- Wed Apr 22, 2020 5:07 pm
- Forum: K-Pro / KManager
- Topic: Launch Control Fuel Enrichment
- Replies: 2
- Views: 1277
- Wed Apr 22, 2020 3:39 pm
- Forum: K-Pro / KManager
- Topic: Launch Control Fuel Enrichment
- Replies: 2
- Views: 1277
Launch Control Fuel Enrichment
I just noticed that Fuel Enrichment under Launch Control changed from % to Units, what units are in reference here? Fuel table units? percent still?
Also, for Ignition Retard, does a positive integer = retard?
Also, for Ignition Retard, does a positive integer = retard?
- Fri Jul 14, 2017 11:51 pm
- Forum: K-Pro / KManager
- Topic: Closed Loop Target Lambda only works for v4?
- Replies: 5
- Views: 2114
Re: Closed Loop Target Lambda only works for v4?
PRB. if i turn it on, it will just correct to 14.7, if i turn it off it follows fuel map. AFCMD stays 14.7 no matter what i change it to.
- Thu Jul 13, 2017 4:51 pm
- Forum: K-Pro / KManager
- Topic: Closed Loop Target Lambda only works for v4?
- Replies: 5
- Views: 2114
Re: Closed Loop Target Lambda only works for v4?
the one from parameters > adv closed loop > target lambda low/high button - which brings up the table window for such
- Sun Jul 09, 2017 5:06 pm
- Forum: K-Pro / KManager
- Topic: Closed Loop Target Lambda only works for v4?
- Replies: 5
- Views: 2114
Closed Loop Target Lambda only works for v4?
I can't seem to get this v3 to change AFCMD from 14.7 to following Target Lambda tables, I just did it on 3 v4 ecus with success. Help file doesn't mention which version supports it, if different. Am I missing something or is it only a v4 thing?
- Tue Apr 26, 2016 4:59 pm
- Forum: K-Pro Calibrations
- Topic: Shaky CAM vs CAMCMD and IGN vs Ign table
- Replies: 2
- Views: 2578
Re: Shaky CAM vs CAMCMD and IGN vs Ign table
thanks i'll look into it
- Mon Apr 25, 2016 7:35 pm
- Forum: K-Pro Calibrations
- Topic: Shaky CAM vs CAMCMD and IGN vs Ign table
- Replies: 2
- Views: 2578
Shaky CAM vs CAMCMD and IGN vs Ign table
I've been noticing for a long time on K24A2 swaps, I see what is posted in the images below. Right now the ignition is causing slight drivability issues customer states feels like heistation, During tuning, the shaky VTC angles are causing the fuel/ign tables to flip flop between all tables (0,10, 2...
- Sun Sep 27, 2015 11:55 pm
- Forum: K-Pro / KManager
- Topic: KPro / KManager requests
- Replies: 146
- Views: 832157
Re: KPro / KManager requests
i've been wanting to have Ctrl+S for Save As... added to Kmanager for a long long time. I like to save my changes often so I can go back easily or flip flop around when troubleshooting. Also the less I have to use the trackpad to point and click for things the better. or even better, if there could ...
- Sat Dec 14, 2013 1:26 pm
- Forum: K-Pro / KManager
- Topic: can you connect new version software to old version ecu?
- Replies: 10
- Views: 5277
Re: can you connect new version software to old version ecu?
i feel like he might have wanted to download his old software off the ecu first... oh well.
- Sat Dec 14, 2013 1:25 pm
- Forum: K-Pro / KManager
- Topic: Running no o2 Sensors with kpro
- Replies: 2
- Views: 3522
Re: Running no o2 Sensors with kpro
you should run at least the primary, you gain nothing by running no o2 sensors.
- Sat Dec 14, 2013 2:05 am
- Forum: K-Pro / KManager
- Topic: VTC phase gap troubleshooting
- Replies: 1
- Views: 3409
VTC phase gap troubleshooting
Hey guys, So we have a P0341 on a K24A1 ep3. Stock block, revhard mani, t3/t4 turbonetics, nothing special. This kit came off the same owners original K20A3, using the same kal and ecu, when everything was working fine. The kal (one of the revhard base maps for ep3), when all cam angles are set to 0...