S300v3 Will Not Rev past 2500 RPMs
S300v3 Will Not Rev past 2500 RPMs
I am having an issue with S300 not allowing me to rev past 2500 rpms at times. This happens when I start the car without my laptop plugged in. It acts as if it is a rev limit activation bouncing from 1500-2500 RPMs. The lighter the throttle the faster it bounces, and the more throttle is given the slower it will bounce. If I plug my laptop into the ECU with SManager up and turn the ignition off, it seems to do a reset and will rev normally with the throttle.
Grounds are good on engine and trans
Using SManager v2.6.6.0
TPS seems to be calibrated properlly, no other issues
No fault codes stored
Grounds are good on engine and trans
Using SManager v2.6.6.0
TPS seems to be calibrated properlly, no other issues
No fault codes stored
- Attachments
-
- 2500rpmlimit.s3d
- (452.42 KiB) Downloaded 131 times
Re: S300v3 Will Not Rev past 2500 RPMs
Oh, and once I've plugged in SManager and got the revs working properlly, I can unplug my laptop with the car running and the revs continue to work until I turn off the ignition and turn it back on.
Re: S300v3 Will Not Rev past 2500 RPMs
Also noticed in Sensors that "REVL" and "IGNC" switch from off to on while the revs are bouncing from 1500 to 2500 rpm. I disabled the full throttle shift and the burnout rev limit, with no resolution.
-
- Posts: 3
- Joined: Wed Aug 08, 2018 9:58 pm
Re: S300v3 Will Not Rev past 2500 RPMs
Can u please upload the calibration ?
Re: S300v3 Will Not Rev past 2500 RPMs
I thought that I did. There is an attachment of it. Is that not the correct way to upload it?
Re: S300v3 Will Not Rev past 2500 RPMs
That is a datalog and not the calibration.
Re: S300v3 Will Not Rev past 2500 RPMs
I see. Try this one then.
- Attachments
-
- alex t85.skl
- (42.09 KiB) Downloaded 164 times
Re: S300v3 Will Not Rev past 2500 RPMs
Are you just doing a test upload?
Re: S300v3 Will Not Rev past 2500 RPMs
I don't know what you mean by a test upload. I tried to upload the calibration I am currently running.
Re: S300v3 Will Not Rev past 2500 RPMs
Step by step tell me exactly what you are clicking to upload.
Re: S300v3 Will Not Rev past 2500 RPMs
I turn the ignition on and press the throttle in which the vehicle bounces from 1500-2500 rpm. I then plug in my laptop with SManager already pulled up with the current calibration, while the vehicle is running. I will then press the arrow key "upload changes to the ECU". This usually does not work, so I will turn the ignition off and back on, then again hit the arrow key to upload changes. Once uploaded, I start the vehicle and it will rev normally. I can then drive the vehicle normally until I shut the engine and ignition off. Then I have to start all over again.
Re: S300v3 Will Not Rev past 2500 RPMs
Close the program, reopen it, load the calibration you want to use, turn the key to the on position with the engine not running and upload the calibration.
Re: S300v3 Will Not Rev past 2500 RPMs
Did the same thing.
Re: S300v3 Will Not Rev past 2500 RPMs
I am running CPR with this setup. Not sure if that makes a difference. I am also using Parallels that is partitioned on my Mac. It's running Windows XP, but this has never given me an issue in the past.
Re: S300v3 Will Not Rev past 2500 RPMs
What is the serial number that is on the s300 board inside the ECU?