7psi base map

Civic 2016+ 1.5 Turbo
Post Reply
coder101
Posts: 1
Joined: Tue May 02, 2017 3:10 pm

7psi base map

Post by coder101 » Tue May 02, 2017 3:19 pm

Hello,

New to this, anyone try the base map personally? I got a 2017 coupe ex-t and thinking of giving it a try.

Thanks

malgeo
Posts: 3
Joined: Sat Aug 19, 2017 8:34 am

Re: 7psi base map

Post by malgeo » Mon Aug 21, 2017 9:33 am

I tried this yesterday. I did a quick 0-60 in roughly 7 seconds. My tires actually squealed a little bit (I don't remember exactly at which point). I'm using the +6psi calibration again just because I'm not sure if it's safe for the CVT to continue at +7psi.

http://www.mediafire.com/file/sz97to6zx8qilqp/7psi.fpdl

Jun43
Posts: 251
Joined: Mon Aug 01, 2016 2:59 pm

Re: 7psi base map

Post by Jun43 » Mon Aug 21, 2017 9:52 am

malgeo wrote:
Mon Aug 21, 2017 9:33 am
I tried this yesterday. I did a quick 0-60 in roughly 7 seconds. My tires actually squealed a little bit (I don't remember exactly at which point). I'm using the +6psi calibration again just because I'm not sure if it's safe for the CVT to continue at +7psi.

http://www.mediafire.com/file/sz97to6zx8qilqp/7psi.fpdl
everything looks normal. are you sure it's not the 6psi map? i dont see a +7 map. judging from the datalogs, it looks like the +6psi map

you let off a little early before hitting 60mph. Could of done it a tad faster

malgeo
Posts: 3
Joined: Sat Aug 19, 2017 8:34 am

Re: 7psi base map

Post by malgeo » Mon Aug 21, 2017 9:58 am

Jun43 wrote:
Mon Aug 21, 2017 9:52 am
everything looks normal
Can you clarify? Do you mean normal like it should be safe for the CVT? or normal like there's no improvement over the +6psi cal? Thanks for your insight. I'm completely new to this.

Jun43
Posts: 251
Joined: Mon Aug 01, 2016 2:59 pm

Re: 7psi base map

Post by Jun43 » Mon Aug 21, 2017 10:01 am

malgeo wrote:
Mon Aug 21, 2017 9:58 am
Jun43 wrote:
Mon Aug 21, 2017 9:52 am
everything looks normal
Can you clarify? Do you mean normal like it should be safe for the CVT? or normal like there's no improvement over the +6psi cal? Thanks for your insight. I'm completely new to this.
post your +7 psi calibration.
your datalog shows it running around 19psi. which is the +6psi map.

normal as in its running like it should be. It's safe

malgeo
Posts: 3
Joined: Sat Aug 19, 2017 8:34 am

Re: 7psi base map

Post by malgeo » Mon Aug 21, 2017 10:58 am

Jun43 wrote:
Mon Aug 21, 2017 10:01 am
malgeo wrote:
Mon Aug 21, 2017 9:58 am
Jun43 wrote:
Mon Aug 21, 2017 9:52 am
everything looks normal
Can you clarify? Do you mean normal like it should be safe for the CVT? or normal like there's no improvement over the +6psi cal? Thanks for your insight. I'm completely new to this.
post your +7 psi calibration.
your datalog shows it running around 19psi. which is the +6psi map.

normal as in its running like it should be. It's safe
Basically I took the +6psi cal and modified the TC maximum pressure ratio from 1500rpm and up by .07 bar (1psi). Assuming this is not the correct way to increase boost to +7psi, how would I go about doing that? Thanks.
http://www.mediafire.com/file/gnvwr9btf ... 7psi.fpcal

efcee
Posts: 3
Joined: Wed Mar 06, 2019 7:12 am

Re: 7psi base map

Post by efcee » Wed Mar 06, 2019 2:14 pm

any news on this?

Post Reply