Anybody can explain if this correct green connector ? Above glove box apartament, didn't had a tester to check :)
TSX 04-06 green connector
Re: TSX 04-06 green connector
Cr-v RD8+K24A2turbo+Kpro V4 prb+NPR3/6Speed+ТС+ HFS4 v3.2.
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper
Re: TSX 04-06 green connector
found myself :)sass wrote:угу
http://www.hondata.com/downloads/04-06_ ... nstall.pdf
Known as Vaikis_
-
- Posts: 2
- Joined: Thu Sep 18, 2014 2:22 pm
Re: TSX 04-06 green connector
Hi Zoro2006 sorry to border you but i recently bought a tsx ecu and a flashpro and i am about to do the CAN programming adapter installation on my 2006 accord 2.4 executive( german version) and i followed the instructions and unmounted the glove box but like you i have two green connectors:number 1 and 2 in the picture that i attached,so my question is did you use the number 1 connector or the number 2 connector as described in the hondata manual :
http://www.hondata.com/downloads/04-06_ ... nstall.pdf
also i wanted to ask you did you do it exactly as described in the hondata manual or did you use an other approach(i am asking cause if i have to do it following the hondata manual and use connector number 2, i would have to solder the two wires to the green connector cause on my green connector there is no empty spot),and also is there something else(except everything mentioned in the hondata manual) i should do before going to the honda dealer for the VIN and immobilizer matching.
once again sorry to border you.thanks a lot best regards Todor
http://www.hondata.com/downloads/04-06_ ... nstall.pdf
also i wanted to ask you did you do it exactly as described in the hondata manual or did you use an other approach(i am asking cause if i have to do it following the hondata manual and use connector number 2, i would have to solder the two wires to the green connector cause on my green connector there is no empty spot),and also is there something else(except everything mentioned in the hondata manual) i should do before going to the honda dealer for the VIN and immobilizer matching.
once again sorry to border you.thanks a lot best regards Todor
- Attachments
-
- green connector.jpg (109.47 KiB) Viewed 6361 times
Re: TSX 04-06 green connector
number 2lamerchebg wrote:Hi Zoro2006 sorry to border you but i recently bought a tsx ecu and a flashpro and i am about to do the CAN programming adapter installation on my 2006 accord 2.4 executive( german version) and i followed the instructions and unmounted the glove box but like you i have two green connectors:number 1 and 2 in the picture that i attached,so my question is did you use the number 1 connector or the number 2 connector as described in the hondata manual :
http://www.hondata.com/downloads/04-06_ ... nstall.pdf
also i wanted to ask you did you do it exactly as described in the hondata manual or did you use an other approach(i am asking cause if i have to do it following the hondata manual and use connector number 2, i would have to solder the two wires to the green connector cause on my green connector there is no empty spot),and also is there something else(except everything mentioned in the hondata manual) i should do before going to the honda dealer for the VIN and immobilizer matching.
once again sorry to border you.thanks a lot best regards Todor
Known as Vaikis_
Re: TSX 04-06 green connector
or a bridge on the can bus just before the ecu in the center lower dash ....like i do with solder and clips.... less effort and cut on hands