Oh ok. I’ll contact the tuners again and see if they’ll send me the unlocked cal. I’ll let you have a look if you think you can sort out the gauges
for me. That would be great.
Cheers
Fuel gauges on supercharged fn2 type r
Re: Fuel gauges on supercharged fn2 type r
Yes, with pleasure, no problem! :-)
Please let me know!
Please let me know!
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Fuel gauges on supercharged fn2 type r
Hi, they seem very reluctant to send me the cal. With respect Prob for the same reason you gave. A lot of effort and time goes into tuning. So I sent them this email.
“Can we do a Hybrid tune on my car with AFM and MAP sensor activated but also tune both AFM and MAP fuel tables. Hopefully this should solve the fuel gauge problem. MAF sensor still ignored so no limp mode.
Sounds promising yes?”
This is basically the way you described your cal so I’ve ran it past them.
“Can we do a Hybrid tune on my car with AFM and MAP sensor activated but also tune both AFM and MAP fuel tables. Hopefully this should solve the fuel gauge problem. MAF sensor still ignored so no limp mode.
Sounds promising yes?”
This is basically the way you described your cal so I’ve ran it past them.
Re: Fuel gauges on supercharged fn2 type r
hi, I have a race map on a fn2 with gt3076r and 1000cc injectors.R-12914 wrote: ↑Fri Jan 19, 2018 2:21 pm For clarification:
AFM/MAF-based map (supported):
afm.JPG
Fuel display (supported):
afm-hybrid.JPG
(AFM/MAF-based maps are without MAP-Fuel tables.)
Hybrid-based map (supported):
hybrid.JPG
Fuel display (supported):
afm-hybrid.JPG
(Hybrid-based maps are with MAP-Fuel tables. In this case MAP-fuel tables are using above 515 mbar manifold air pressure depending on the load condition and below it uses MAF.)
MAP-based calibration (supported)
map.JPG
Fuel display (supported):
afm-hybrid.JPG
Race-based map (no longer supported):
race.JPG
Fuel display (not supported):
(On Race Maps the fuel gauge does not read correctly and is not adjustable!)
to change from race map to regular map using only MAP tables, can I directly copy my fuel tables and ignition from my RACE map to the new map, and would it work well? or change the fuel tables?
any way to make the conversion?
regards
Re: Fuel gauges on supercharged fn2 type r
Theoretically yes... But I recomment to check the datalog after switching to the RSP based ECU calibration. (The correct one for the FN2)tiozes wrote: ↑Sun Mar 04, 2018 4:39 pm
hi, I have a race map on a fn2 with gt3076r and 1000cc injectors.
to change from race map to regular map using only MAP tables, can I directly copy my fuel tables and ignition from my RACE map to the new map, and would it work well? or change the fuel tables?
any way to make the conversion?
regards
Dont forget to set => 0 in the fuel section => "use MAP tables"
Additional: WOT Lambda adjustment low and high:
This table is editiable in race calibrations only from col 1 to 10.
In the RSP based you must tune the full table 1 to 20!!
On supercharged applications I have good results with this:
Dont forget to check RPM and MAP pressure! This could be different from each tune. Depending from your tuner...
Re: Fuel gauges on supercharged fn2 type r
Hi, I have migrated everything I've seen from the RACE map to the regular map, but I do not know if I'm missing anything.typer86 wrote: ↑Mon Mar 05, 2018 12:28 amTheoretically yes... But I recomment to check the datalog after switching to the RSP based ECU calibration. (The correct one for the FN2)tiozes wrote: ↑Sun Mar 04, 2018 4:39 pm
hi, I have a race map on a fn2 with gt3076r and 1000cc injectors.
to change from race map to regular map using only MAP tables, can I directly copy my fuel tables and ignition from my RACE map to the new map, and would it work well? or change the fuel tables?
any way to make the conversion?
regards
Dont forget to set => 0 in the fuel section => "use MAP tables"
Additional: WOT Lambda adjustment low and high:
This table is editiable in race calibrations only from col 1 to 10.
In the RSP based you must tune the full table 1 to 20!!
On supercharged applications I have good results with this:
Dont forget to check RPM and MAP pressure! This could be different from each tune. Depending from your tuner...
WOT-low.png
WOT-high.png
my tuner has disappeared and no one in Spain that provides the service, since everyone wants to tune in from 0, but my car is perfect as well.
If I send you the map, would you be so kind as to review it?
I imagine that after loading the new map I would have to monitor the A / F in case it fails, right?
Greetings and thanks
Re: Fuel gauges on supercharged fn2 type r
Help please